• Design for a Cause 2021 - Blog #2: BuzzBeat v2.0!

    Hello! Its been 3 weeks since my last blog, 2 reasons contributed to the delay mainly - - I got infected with the Coronavirus - My challenger's kit got delayed by a couple of weeks   Anyway, I am fine and wel...
    Profile Photo
    last modified by thebluephoenix
  • Trakcore #1 AI Assisted Posture Modification - Project Introduction

    Design for A Cause 2021Trakcore #1 AI Assisted Posture Modification - Project Introduction #1 - Project Introduction #2 - Acquiring Data and Designing a Model #3 - Deploying and Testing Edge Impulse ML Model on Ard...
    Profile Photo
    last modified by vlasov01
  • Trakcore #2 AI Assisted Posture Modification - Acquiring Data and Designing a Model

    Design for A Cause 2021Trakcore #1 AI Assisted Posture Modification - Project Introduction #1 - Project Introduction #2 - Acquiring Data and Designing a Model #3 - Deploying and Testing Edge Impulse ML Model on Ard...
    Profile Photo
    last modified by vlasov01
  • Trakcore #3 AI Assisted Posture Modification - Deploying and Testing Edge Impulse ML Model on Arduino Nano 33 IoT

    Design for A Cause 2021Trakcore #1 AI Assisted Posture Modification - Project Introduction #1 - Project Introduction #2 - Acquiring Data and Designing a Model #3 - Deploying and Testing Edge Impulse ML Model on Ard...
    Profile Photo
    last modified by vlasov01
  • Smart Exhibit: Blog #4: Electronic schematic, system building and sanity checks

    Hello!   As explained in my previous blog post ( Smart Exhibit: Blog #3: The hardware components ), I need some extra components (temperature, humidity, light, sound and motion sensors, speaker, push-button, bat...
    Profile Photo
    last modified by alexandru.cohal
  • VenTTracker #06 -  Window Sensor Prototype

      Design for A Cause 2021 the VenTTracker project 01 - Intro and motivation. | 02 - Analyzing Window Types (I) | 03 - Analyzing Window Types (II) | 04 - Playing with the IMU |  05-Sliding Window Mock-up | 06...
    Profile Photo
    last modified by javagoza
  • VenTTracker #01 - Intro and motivation.

      Design for A Cause 2021 the VenTTracker project   01 - Intro and motivation. | 02 - Analyzing Window Types (I) | 03 - Analyzing Window Types (II) | 04 - Playing with the IMU | 05-Sliding Window Mock-up | V...
    Profile Photo
    last modified by javagoza
  • VenTTracker #02 -  Analyzing window types.

      Design for A Cause 2021 the VenTTracker project   01 - Intro and motivation. | 02 - Analyzing Window Types (I) | 03 - Analyzing Window Types (II) | 04 - Playing with the IMU | 05-Sliding Window Mock-up | V...
    Profile Photo
    last modified by javagoza
  • VenTTracker #03 -  Analyzing window types II

      Design for A Cause 2021 the VenTTracker project 01 - Intro and motivation. | 02 - Analyzing Window Types (I) | 03 - Analyzing Window Types (II) | 04 - Playing with the IMU | 05-Sliding Window Mock-up| VenTTra...
    Profile Photo
    last modified by javagoza
  • VenTTracker #04 -  Playing with the IMU

      Design for A Cause 2021 the VenTTracker project 01 - Intro and motivation. | 02 - Analyzing Window Types (I) | 03 - Analyzing Window Types (II) | 04 - Playing with the IMU | 05-Sliding Window Mock-up | VenTTrac...
    Profile Photo
    last modified by javagoza
  • VenTTracker #05 -  Sliding Window Mock-up

      Design for A Cause 2021 the VenTTracker project 01 - Intro and motivation. | 02 - Analyzing Window Types (I) | 03 - Analyzing Window Types (II) | 04 - Playing with the IMU | 05-Sliding Window Mock-up | VenTTrac...
    Profile Photo
    last modified by javagoza
  • BLOG# 1 - Beats Per Minute Nano - INTRODUCTION

    BLOG# 1 - Beats Per Minute Nano A Heart Rate Monitor using the Arduino Nano 33 IoT Board INTRODUCTION This is my Introductory blog post for this Design Challenge: Design for A Cause 2021 version 1.1   For this ...
    Profile Photo
    last modified by skruglewicz
  • Blog# 2 Beats Per Minute Nano - Research & Experimentation

    BLOG# 2 - Beats Per Minute Nano A Heart Rate Monitor using the Arduino Nano 33 IoT Board Research & Experimentation This is my 2nd blog post in a series of blog post for the Design Challenge: Design for A Cause...
    Profile Photo
    last modified by skruglewicz
  • VenTTracker - Window Sensor Prototype Disassembly Reversed

    Open video

    Profile Photo
    last modified by javagoza
  • VenTTracker - Window Sensor Prototype Demo

    Open video

    Profile Photo
    last modified by javagoza
  • OLED Experiment

    Open video

    Profile Photo
    last modified by skruglewicz
  • OLED Experiment

    Open video

    Profile Photo
    last modified by skruglewicz
  • Arduino Nano 33 IoT for Early Warning Detection for Landslide

    Landslide Introduction   Landslides or often called soil movements are a geological event that occurs due to the movement of masses of rocks or soil with various types and types such as falling rocks or large lum...
    Profile Photo
    last modified by ahmadradhy
  • Design For A Cause 2021 - Challengers Announcement

    Design for a Cause 2021 Challenge About this Challenge | Dates | The Judges | The Kit | The Prizes | Technical Resources | Example Application | Terms & Conditions | The Challengers   Congratulations to ...
    Profile Photo
    last modified by e14phil
  • Nano 33 IoT with Qubitro IoT Platform

    Also, it is used to collect the accelerometer data using arduino nano 33 IoT. Using MQTT by Qubitro library is very possible to send all data to the qubitro’s IoT cloud https://www.qubitro.com/.    ...
    Profile Photo
    last modified by ahmadradhy