Skip navigation

PiCasso Design Challenge

9 Posts authored by: dwinhold
POV Globe blog #8   This update is showing the power hooked up and working through the bearings and a test of the globe with temporary LED's. I feel the 2 videos will explain a lot more, so here they are (Sorry for the moving camera):       So the next blog will be the programing of the colour LED's and final setup. The 10th blog will be the completed project!!   Please leave any questions or comments!!   Dale Winhold ...
Welcome back for the 2nd part of my 7th blog. This part is the motor turning the globe, proving the sewing maching motor works. The video below shows it working.     Thank you   Dale W ...
For the 7th update (Part 1 of 2) I have come up with a motor that should work. I bought an old sewing machine and removed the motor. I took apart the foot control and mounted it to my project so now it is hand controled. Below are pictures and a short video of how it works. Part B will be in a couple of days as I have to hook up the motor to the project and align everything.   First picture is of the disassembled sewing machine. I took about an hour:     The removed motor:  ...
This update is the wiring of the power to the globe. The below photos and explanations of each, describe exactly what I did. I also include a video at the end.   First photo is of the Positive wires that power the Raspberry Pi and the LED's:     Next is the Negative out:     Next photo is of the underside at the bearings. The spindle is hand made of wood on a wood lathe. I drilled a hole down the middle for the wire to travel:     The last is a video ...
Blog 5 update is the drive system for the globe to spin. I am using a pully system with a rotary tool as the motor. After lots of testing over the past week I found that the motor can't handle the tension and started to burn up. This is a little setback, but it did work so I just need to use a different motor. I am thinking of using a sewing maching motor as they are stronger and have a speed of up to 7000 rpm.   Below are pictures of the setup:       This update is fai ...
Welcome to my 4th Blog of the POV Globe. The subject of this update isn't what I has planned on, it was to be about hooking up the motor and get the globe turning. Unfortunately the motor I have isn't powerful enough to get up to the speed I require. I will have to source out a stronger and faster motor for my next blog. This is just a very minor setback.   So this blog is about how I am getting the power to the Raspberry Pi and the LED's. Like I said in my last blog, I was wanting to run ...
Hi everyone,   This weeks update is a bit more then I figured. I got quite a bit completed on the building of the globe. As you will see I created the base for the globe, top part to support the north end of the globe and have the LED's attached. I am trying to see if I can make it more 3D by giving it depth with a second row of LED's on the inside of the globe. This way I can produce 2 pictures at 2 different depths at the same time. As always, anyone want any of the .dxf files for this p ...
Hello everyone!!   I already received the Raspberry Pi kit from the courier. That was very fast!! As we all know, the kit contained a Raspberry Pi complete starter kit, PiFace digital 2 and the Pi Camera v2. Thank you to our sponsor for this great kit!!   So for this weeks update:   For starting the globe I had to think this in reverse "reverse engineer everything". I had to figure how many LED's I plan on using, in order to calculate the diameter of the globe. Since I am using ...
Hello Community,   Here is the introduction to my project POV Globe. I have been fastenated for years with Persistence of Vision (POV). I have created POV wands for my kids, but I have always wanted to create a globe. I want to go into great depths with this, starting with making it colour. The extent of what graphics I create will depend on the time alloted. I do promise not to disappoint!!   POV Globe Persistence of vision traditionally refers to the optical illusion that occurs w ...