Version 37

     

    All 20 of the sponsored Challengers for the Sixth Sense Design Challenge will receive for FREE the kit detailed in the table below. 

    Our judges will choose 20 applicants to become sponsored challengers, and they will receive the kit free of charge.

    If you are not a sponsored challenger, you can still compete as a non-sponsored or independent challenger.  See note below.*

     

    Featured Products

    From STMicroelectronics:

    SensorTile Development KitSensorTile Development Kit

    STM32 Nucleo-64STM32 Nucleo-64

     

    From TE Connectivity:

    KMT32BKMT32B or KMT36H

    FX19FX19

    PTF Series RTD Sensor

     

    Once the sponsored Challengers receive their kit, they will then embark on their journey of designing an exciting and original project that uses the  STMicroelectronics Sensor Tile and TE Connectivity Component PackSTMicroelectronics Sensor Tile and TE Connectivity Component Pack to give a Sixth Sense to a small remotely operated or autonomous vehicle, such as a drone, robot, or tunnel exploration device.

     

    *NOTE: Even if you aren't a sponsored challenger, you can still participate in the Design Challenge as long as you integrate the STMicroelectronics Sensor Tile and TE Connectivity Component Pack into your design.

     

    The deadline for project application submissions is 19th November 2018.

     

     

    The Kit Buy Kit*Buy Kit*

    SensorTile Development Kit  STEVAL-STLKT01V1STEVAL-STLKT01V1

    The  STEVAL-STLKT01V1STEVAL-STLKT01V1 is a comprehensive development kit designed to support and expand the capabilities of the SensorTile It is complemented with software firmware libraries and tools including a dedicated mobile app The SensorTile is a tiny square-shaped IoT module with powerful processing capabilities to leverage a high-performance Arm Cortex-M4 32-bit RISC core 80 MHz STM32L476JGY microcontroller It has on-board Bluetooth low energy connectivity based on BlueNRG-MS network processor as well as a wide spectrum of motion and environmental MEMS sensors including a digital microphone

     

    32Bit MCU

    3D Accelerometer

    3D Gyroscope

    Microphone

    Bluetooth LE

    Li-Ion Battery

    Buy NowBuy Now

    STM32 Nucleo-64, STM32F411RE

    The  NUCLEO-F411RENUCLEO-F411RE is an STM32 Nucleo development board with an STM32F411RET6 microcontroller that allows users to build their own prototypes for embedded applications The Arduino connectivity support and ST Morpho headers make it easy to expand the functionality of the STM32 Nucleo open development platform with specialized shields The STM32 Nucleo board does not require any separate probe as it integrates the ST-LINK/V2-1 debugger/programmer

     

    STM32F411RET6 microcontroller

    Arduino Uno Revision 3 connectivity and STMicroelectronics Morpho extension resources supported

    Onboard ST-LINK/V2-1 debugger/programmer with SWD connector

    Buy NowBuy Now

    KMT32B or KMT36H Magnetic Angle Sensor

    The KMT32B is a magnetic field sensor based on the anisotropic magneto resistance effect, i.e. it senses the magnetic field direction independently of the magnetic field strength for applied field strengths H>25 kA/m. The sensor contains two parallel supplied Wheatstone bridges, which enclose a sensitive angle of 45 degrees.

     

    Contactless angular position, ideal for harsh environments

    Self-diagnosis feature

    High accuracy, extended operating temperature range

    Buy NowBuy Now

    FX1901 Compression Load Cell

    The FX1901 is a 1% load cell device with full scale ranges of 10, 25, 50 or 100 and 200lbf compression. This technology enables force sensing in a whole new class of "smart" consumer and medical products. Operating at very low strains, Microfused™ technology provides an essentially unlimited cycle life expectancy, superior resolution, high over-range capabilities, and a ratiometric span of 20mV/V.

     

    10 - 200lbf ranges

    Compact coin cell package, anti-rotation mounting features

    Low noise, high reliability, low deflection

    Buy NowBuy Now

    PTF Series RTD Sensor

    The PTF-sensor family combines a group of resistance temperature detectors (RTD) using a Platinum resistor in thin film technology as sensing element. The usage of platinum as resistive material guarantees high long term stability. Due to a small outline and low mass this RTD has a low time constant; therefore, it is a suitable solution for fast and precise feedback control systems.

     

    Sensing Temperature Min: -50°C to 600°C

    Low drift over lifetime

    Fast response time because of low thermal mass

    Buy NowBuy Now

     

    Interested in joining the Challengers? You can do it as a non-sponsored Challenger! Here's how:

    Simply purchase the low-cost STMicroelectronics Sensor Tile and TE Connectivity Component PackSTMicroelectronics Sensor Tile and TE Connectivity Component Pack, integrate it into your project, and post 10 blogs about your design journey in the Sixth Sense space, tagging your blogs 'Sixth Sense.'  Then you'll be eligible to win the awesome prizes!