17 Replies Latest reply on Apr 30, 2016 5:43 AM by tushar panda

    hdmi not ready error

    arunmagesh

      hello, i just installed linaro on my board. its connected to my monitor by hdmi,

      i enabled the hdmi in cmd mode too. but it posts error like hdmi no ready in serial debug.

        • Re: hdmi not ready error
          tushar panda

          which OS are you using Linux / Android ??

          plz share the link form where you downloaded the image.

            • Re: hdmi not ready error
              arunmagesh

              i am on linux linaro. downloaded from the riotboard.org

                • Re: hdmi not ready error
                  tushar panda

                  the error belongs to the audio part, not the display.

                  Display should work fine.

                    • Re: hdmi not ready error
                      arunmagesh

                      nope. no response in the display.

                        • Re: hdmi not ready error
                          tushar panda

                          uboot params for HDMI :

                          setenv bootargs console=ttymxc1,115200 init=/init nosmp video=mxcfb0:dev=hdmi,720x480M@60,bpp=32 video=mxcfb1:off fbmem=10M vmalloc=400M androidboot.console=ttymxc1 androidboot.hardware=freescale

                           

                          can you try the above in your uboot settings.

                            • Re: hdmi not ready error
                              arunmagesh

                              i have tried this in the uboot cmd. still no use. tried several resolution too.

                                • Re: hdmi not ready error
                                  tushar panda

                                  can you share the error log here .

                                    • Re: hdmi not ready error
                                      arunmagesh

                                      U-Boot 2009.08-00695-g055df3a (Dec 25 2013 - 09:56:12)

                                       

                                       

                                      CPU: Freescale i.MX6 family TO1.1 at 792 MHz

                                       

                                      Thermal sensor with ratio = 185

                                       

                                      Temperature:   43 C, calibration data 0x5905115f

                                       

                                      mx6q pll1: 792MHz

                                       

                                      mx6q pll2: 528MHz

                                       

                                      mx6q pll3: 480MHz

                                       

                                      mx6q pll8: 50MHz

                                       

                                      ipg clock     : 66000000Hz

                                       

                                      ipg per clock : 66000000Hz

                                       

                                      uart clock    : 80000000Hz

                                       

                                      cspi clock    : 60000000Hz

                                       

                                      ahb clock     : 132000000Hz

                                       

                                      axi clock   : 198000000Hz

                                       

                                      emi_slow clock: 99000000Hz

                                       

                                      ddr clock     : 396000000Hz

                                       

                                      usdhc1 clock  : 198000000Hz

                                       

                                      usdhc2 clock  : 198000000Hz

                                       

                                      usdhc3 clock  : 198000000Hz

                                       

                                      usdhc4 clock  : 198000000Hz

                                       

                                      nfc clock     : 24000000Hz

                                       

                                      Board: i.MX6DL/Solo-SABRESD: unknown-board Board: 0x61011 [POR ]

                                       

                                      Boot Device: MMC

                                       

                                      I2C:   ready

                                       

                                      DRAM:   1 GB

                                       

                                      MMC:   FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2,FSL_USDHC: 3

                                       

                                      In:    serial

                                       

                                      Out:   serial

                                       

                                      Err:   serial

                                       

                                      Net:   got MAC address from IIM: 00:00:00:00:00:00

                                       

                                      ----enet_board_init: phy reset

                                       

                                      FEC0 [PRIME]

                                       

                                      Hit any key to stop autoboot:  3     2     1     0

                                       

                                      mmc3(part 0) is current device

                                       

                                       

                                      MMC read: dev # 3, block # 2048, count 8192 ... 8192 blocks read: OK

                                       

                                      ## Booting kernel from Legacy Image at 10800000 ...

                                       

                                         Image Name:   Linux-3.0.35-02871-ga35ffe3

                                       

                                         Image Type:   ARM Linux Kernel Image (uncompressed)

                                       

                                         Data Size:    3901664 Bytes =  3.7 MB

                                       

                                         Load Address: 10008000

                                       

                                         Entry Point:  10008000

                                       

                                         Verifying Checksum ... OK

                                       

                                         Loading Kernel Image ... OK

                                       

                                      OK

                                       

                                       

                                      Starting kernel ...

                                       

                                       

                                      Linux version 3.0.35-02871-ga35ffe3 (luofc@embest-tech) (gcc version 4.6.2 20110630 (prerelease) (Freescale MAD -- Linaro 2011.07 -- Built at 2011/08/10 09:20) ) #1 SMP PREEMPT Wed Oct 30 15:27:47 CST 2013

                                      CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d

                                      CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache

                                      Machine: Freescale i.MX 6Solo RIOT Board

                                      Ignoring unrecognised tag 0x54410008

                                      Memory policy: ECC disabled, Data cache writealloc

                                      CPU identified as i.MX6DL/SOLO, silicon rev 1.1

                                      PERCPU: Embedded 7 pages/cpu @8c008000 s5440 r8192 d15040 u32768

                                      Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 227328

                                      Kernel command line: console=ttymxc1,115200 init=/init nosmp video=mxcfb0:dev=hdmi,1280x720M@60,bpp=32 video=mxcfb1:off fbmem=10M vmalloc=400M root=/dev/mmcblk0p1 rootwait

                                      PID hash table entries: 4096 (order: 2, 16384 bytes)

                                      Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

                                      Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

                                      Memory: 640MB 256MB = 896MB total

                                      Memory: 896840k/896840k available, 151736k reserved, 0K highmem

                                      Virtual kernel memory layout:

                                          vector  : 0xffff0000 - 0xffff1000   (   4 kB)

                                          fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)

                                          DMA     : 0xf4600000 - 0xffe00000   ( 184 MB)

                                          vmalloc : 0xc0800000 - 0xf2000000   ( 792 MB)

                                          lowmem  : 0x80000000 - 0xc0000000   (1024 MB)

                                          pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)

                                          modules : 0x7f000000 - 0x7fe00000   (  14 MB)

                                            .init : 0x80008000 - 0x8003c000   ( 208 kB)

                                            .text : 0x8003c000 - 0x80a9bd14   (10624 kB)

                                            .data : 0x80a9c000 - 0x80b0a600   ( 442 kB)

                                             .bss : 0x80b0a624 - 0x80b586cc   ( 313 kB)

                                      SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

                                      Preemptible hierarchical RCU implementation.

                                      NR_IRQS:624

                                      MXC GPIO hardware

                                      sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms

                                      Set periph_clk's parent to pll2_pfd_400M!

                                      arm_max_freq=1GHz

                                      MXC_Early serial console at MMIO 0x21e8000 (options '115200')

                                      bootconsole [ttymxc1] enabled

                                      Console: colour dummy device 80x30

                                      Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)

                                      pid_max: default: 32768 minimum: 301

                                      Mount-cache hash table entries: 512

                                      CPU: Testing write buffer coherency: ok

                                      hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available

                                      Brought up 1 CPUs

                                      SMP: Total of 1 processors activated (1581.05 BogoMIPS).

                                      print_constraints: dummy:

                                      NET: Registered protocol family 16

                                      print_constraints: vddpu: 725 <--> 1300 mV at 700 mV fast normal

                                      print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal

                                      print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal

                                      print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal

                                      print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal

                                      print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal

                                      ----ldb_init

                                      ----enable clko2

                                      hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.

                                      hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.

                                      hw-breakpoint: maximum watchpoint size is 4 bytes.

                                      L310 cache controller enabled

                                      l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x02050000, Cache size: 524288 B

                                      bio: create slab <bio-0> at 0

                                      mxs-dma mxs-dma-apbh: initialized

                                      print_constraints: VDDA: 2500 mV

                                      print_constraints: VDDIO: 3300 mV

                                      machine_constraints_voltage: VDDD: unsupportable voltage constraints

                                      reg-fixed-voltage reg-fixed-voltage.2: Failed to register regulator: -22

                                      reg-fixed-voltage: probe of reg-fixed-voltage.2 failed with error -22

                                      print_constraints: vmmc: 3300 mV

                                      SCSI subsystem initialized

                                      spi_imx imx6q-ecspi.0: probed

                                      usbcore: registered new interface driver usbfs

                                      usbcore: registered new interface driver hub

                                      usbcore: registered new device driver usb

                                      Freescale USB OTG Driver loaded, $Revision: 1.55 $

                                      mc_pfuze 1-0008: recv failed!:-5,80

                                      mc_pfuze: probe of 1-0008 failed with error -1

                                      imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)

                                      mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 driver probed

                                      mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 dphy version is 0x3130302a

                                      MIPI CSI2 driver module loaded

                                      Advanced Linux Sound Architecture Driver Version 1.0.24.

                                      Bluetooth: Core ver 2.16

                                      NET: Registered protocol family 31

                                      Bluetooth: HCI device and connection manager initialized

                                      Bluetooth: HCI socket layer initialized

                                      Bluetooth: L2CAP socket layer initialized

                                      Bluetooth: SCO socket layer initialized

                                      i2c-core: driver [max17135] using legacy suspend method

                                      i2c-core: driver [max17135] using legacy resume method

                                      Switching to clocksource mxc_timer1

                                      cfg80211: Calling CRDA to update world regulatory domain

                                      NET: Registered protocol family 2

                                      IP route cache hash table entries: 32768 (order: 5, 131072 bytes)

                                      TCP established hash table entries: 131072 (order: 8, 1048576 bytes)

                                      TCP bind hash table entries: 65536 (order: 7, 786432 bytes)

                                      TCP: Hash tables configured (established 131072 bind 65536)

                                      TCP reno registered

                                      UDP hash table entries: 512 (order: 2, 16384 bytes)

                                      UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)

                                      NET: Registered protocol family 1

                                      RPC: Registered named UNIX socket transport module.

                                      RPC: Registered udp transport module.

                                      RPC: Registered tcp transport module.

                                      RPC: Registered tcp NFSv4.1 backchannel transport module.

                                      PMU: registered new PMU device of type 0

                                      Static Power Management for Freescale i.MX6

                                      wait mode is enabled for i.MX6

                                      cpaddr = c0820000 suspend_iram_base=c08b8000

                                      PM driver module loaded

                                      IMX usb wakeup probe

                                      add wake up source irq 75

                                      IMX usb wakeup probe

                                      cpu regulator mode:ldo_enable

                                      i.MXC CPU frequency driver

                                      JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.

                                      msgmni has been set to 1751

                                      alg: No test for stdrng (krng)

                                      io scheduler noop registered

                                      io scheduler deadline registered

                                      io scheduler cfq registered (default)

                                      mxc_mipi_dsi mxc_mipi_dsi: i.MX MIPI DSI driver probed

                                      MIPI DSI driver module loaded

                                      mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi

                                      mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0x1a:0xa0:0xc1

                                      fbcvt: 1280x720@60: CVT Name - .921M9

                                      imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)

                                      Console: switching to colour frame buffer device 160x45

                                      mxc_sdc_fb mxc_sdc_fb.1: Can't get fb option for mxcfb1!

                                      imx-sdma imx-sdma: loaded firmware 1.1

                                      imx-sdma imx-sdma: initialized

                                      Serial: IMX driver

                                      imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX

                                      imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX

                                      console [ttymxc1] enabled, bootconsole disabled

                                      console [ttymxc1] enabled, bootconsole disabled

                                      imx-uart.2: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX

                                      loop: module loaded

                                      m25p80 spi0.0: unrecognized JEDEC id ffffff

                                      GPMI NAND driver registered. (IMX)

                                      vcan: Virtual CAN interface driver

                                      CAN device driver interface

                                      flexcan netdevice driver

                                      FEC Ethernet Driver

                                      fec_enet_mii_bus: probed

                                      ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

                                      fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller

                                      fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1

                                      fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000

                                      fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00

                                      hub 1-0:1.0: USB hub found

                                      hub 1-0:1.0: 1 port detected

                                      add wake up source irq 72

                                      fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller

                                      fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2

                                      fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200

                                      fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00

                                      hub 2-0:1.0: USB hub found

                                      hub 2-0:1.0: 1 port detected

                                      Initializing USB Mass Storage driver...

                                      usbcore: registered new interface driver usb-storage

                                      USB Mass Storage support registered.

                                      ARC USBOTG Device Controller driver (1 August 2005)

                                      mousedev: PS/2 mouse device common for all mice

                                      generic touchscreen driver, <@>.

                                      usb 2-1: new high speed USB device number 2 using fsl-ehci

                                      hub 2-1:1.0: USB hub found

                                      hub 2-1:1.0: 4 ports detected

                                      >>>>> ct365_get_vendor() called <<<<<

                                      Chip ID: 0x0

                                      Chip data allocation failed: 0x0

                                      i2c-core: driver [generic_ts] using legacy suspend method

                                      i2c-core: driver [generic_ts] using legacy resume method

                                      i2c-core: driver [isl29023] using legacy suspend method

                                      i2c-core: driver [isl29023] using legacy resume method

                                      snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0

                                      i2c /dev entries driver

                                      Linux video capture interface: v2.00

                                      ----ov2656_probe

                                      ----mx6_csi0_io_init

                                      ----v4l2_int_device_register success

                                      mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16

                                      mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17

                                      i2c-core: driver [mag3110] using legacy suspend method

                                      i2c-core: driver [mag3110] using legacy resume method

                                      imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)

                                      Bluetooth: Virtual HCI driver ver 1.3

                                      Bluetooth: HCI UART driver ver 2.2

                                      Bluetooth: HCIATH3K protocol initialized

                                      Bluetooth: Generic Bluetooth USB driver ver 0.6

                                      usbcore: registered new interface driver btusb

                                      sdhci: Secure Digital Host Controller Interface driver

                                      sdhci: Copyright(c) Pierre Ossman

                                      mmc0: SDHCI controller on platform [sdhci-esdhc-imx.3] using ADMA

                                      mmc1: SDHCI controller on platform [sdhci-esdhc-imx.1] using ADMA

                                      mmc2: SDHCI controller on platform [sdhci-esdhc-imx.2] using ADMA

                                      mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed

                                      VPU initialized

                                      mxc_asrc registered

                                      Thermal calibration data is 0x5905115f

                                      Thermal sensor with ratio = 185

                                      Anatop Thermal registered as thermal_zone0

                                      anatop_thermal_probe: default cooling device is cpufreq!

                                      usbcore: registered new interface driver usbhid

                                      usbhid: USB HID core driver

                                      usbcore: registered new interface driver snd-usb-audio

                                      mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio

                                      Cirrus Logic CS42888 ALSA SoC Codec Driver

                                      i2c-core: driver [cs42888] using legacy suspend method

                                      i2c-core: driver [cs42888] using legacy resume method

                                      ----sab_sgtl5000_init

                                      ----enable clko_clk.

                                      sgtl5000 0-000a: Failed to get supply 'VDDD': -19

                                      print_constraints: 0-000a: 850 <--> 1600 mV at 1200 mV normal

                                      sgtl5000 0-000a: sgtl5000 revision 17

                                      mmc0: new high speed DDR MMC card at address 0001

                                      mmcblk0: mmc0:0001 MMC04G 3.57 GiB

                                      mmcblk0boot0: mmc0:0001 MMC04G partition 1 2.00 MiB

                                      mmcblk0boot1: mmc0:0001 MMC04G partition 2 2.00 MiB

                                      mmcblk0: p1

                                      mmcblk0boot1: unknown partition table

                                      mmcblk0boot0: unknown partition table

                                      asoc: sgtl5000 <-> imx-ssi.1 mapping ok

                                      imx_3stack asoc driver

                                      asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok

                                      ALSA device list:

                                        #0: sgtl5000-audio

                                        #1: imx-hdmi-soc

                                      NET: Registered protocol family 26

                                      TCP cubic registered

                                      NET: Registered protocol family 17

                                      can: controller area network core (rev 20090105 abi 8)

                                      NET: Registered protocol family 29

                                      can: raw protocol (rev 20090105)

                                      can: broadcast manager protocol (rev 20090105 t)

                                      Bluetooth: RFCOMM TTY layer initialized

                                      Bluetooth: RFCOMM socket layer initialized

                                      Bluetooth: RFCOMM ver 1.11

                                      Bluetooth: BNEP (Ethernet Emulation) ver 1.3

                                      Bluetooth: BNEP filters: protocol multicast

                                      Bluetooth: HIDP (Human Interface Emulation) ver 1.2

                                      lib80211: common routines for IEEE802.11 drivers

                                      VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4

                                      Bus freq driver module loaded

                                      Bus freq driver Enabled

                                      mxc_dvfs_core_probe

                                      DVFS driver module loaded

                                      snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:05:20 UTC (320)

                                      EXT3-fs: barriers not enabled

                                      kjournald starting.  Commit interval 5 seconds

                                      EXT3-fs (mmcblk0p1): using internal journal

                                      EXT3-fs (mmcblk0p1): 13 orphan inodes deleted

                                      EXT3-fs (mmcblk0p1): recovery complete

                                      EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode

                                      VFS: Mounted root (ext3 filesystem) on device 179:1.

                                      Freeing init memory: 208K

                                      Failed to execute /init.  Attempting defaults...

                                      modprobe: FATAL: Could not load /lib/modules/3.0.35-02871-ga35ffe3/modules.dep: No such file or directory

                                       

                                       

                                      modprobe: FATAL: Could not load /lib/modules/3.0.35-02871-ga35ffe3/modules.dep: No such file or directory

                                       

                                       

                                      modprobe: FATAL: Could not load /lib/modules/3.0.35-02871-ga35ffe3/modules.dep: No such file or directory

                                       

                                       

                                       

                                      Last login: Thu Jan  1 00:04:26 UTC 1970 on tty1

                                      * Starting Advanced Power Management daemon...        [80G

                                      [74G[ OK ]

                                      speech-dispatcher disabled; edit /etc/default/speech-dispatcher

                                      Checking for running unattended-upgrades:

                                      ERROR: v4l2 capture: slave not found!

                                      ov2656_read_reg:write reg error:reg=300a

                                      * Starting bluetooth        [80G Welcome to Linaro 11.10 (development branch) (GNU/Linux 3.0.35-02871-ga35ffe3 armv7l)

                                       

                                      * Documentation:  https://wiki.linaro.org/

                                       

                                      New release '12.04 LTS' available.

                                      Run 'do-release-upgrade' to upgrade to it.

                                       

                                       

                                      [74G[ OK ]

                                        [33m* [39;49m PulseAudio configured for per-user sessions

                                      saned disabled; edit /etc/default/saned

                                      1 Jan 00:05:47 ntpdate[5398]: no servers can be used, exiting

                                      root@linaro-ubuntu-desktop:~# ERROR: HDMI is not ready!

                                      asoc: can't open platform imx-hdmi-soc-audio.0

                                      ERROR: HDMI is not ready!

                                      asoc: can't open platform imx-hdmi-soc-audio.0

                                      ERROR: HDMI is not ready!

                                      asoc: can't open platform imx-hdmi-soc-audio.0

                                      ERROR: HDMI is not ready!

                                      asoc: can't open platform imx-hdmi-soc-audio.0

                                      ERROR: HDMI is not ready!

                                      asoc: can't open platform imx-hdmi-soc-audio.0

                                      ERROR: HDMI is not ready!

                                      asoc: can't open platform imx-hdmi-soc-audio.0

                                      ERROR: HDMI is not ready!

                                      asoc: can't open platform imx-hdmi-soc-audio.0

                                      ERROR: HDMI is not ready!

                                      asoc: can't open platform imx-hdmi-soc-audio.0

                        • Re: hdmi not ready error
                          tushar panda

                          plz share the error bootlog also.

                          • Re: hdmi not ready error
                            tushar panda

                            arun,

                             

                            as posted above, plz try and confirm.

                            the above is the only setting in 3.0.35 BSP to get HDMI working.

                            • Re: hdmi not ready error
                              tushar panda

                              1280*720  works perfect with riotboard.

                              plz update uboot params here with above resolution and try.

                              • Re: hdmi not ready error
                                rashmisharma

                                using all the above methods i still getting HDMI video is not ready.

                                mine is 3.19.0-25-generic linux version