3 Replies Latest reply on Aug 16, 2011 1:26 AM by jeromeabcpcb

    Abort : Internal polygon error 71

    jeromeabcpcb

      Hello,

       

      I have a large board (500x200mm) with multiple polygons for supply planes.

      At some point when I move the edges of the polygons I get a Abort : internal

      polygon error 71 message, then Eagle closes.

       

      What causes such error ? Any work around ?

       

      Thanks,

       

      Best regards,

       

      Jerome

       

       

        • Re: Abort : Internal polygon error 71
          Richard_H

          Am 10.08.2011 14:07, schrieb Jerome:

          Hello,

           

          I have a large board (500x200mm) with multiple polygons for supply planes.

          At some point when I move the edges of the polygons I get a Abort :

          internal polygon error 71 message, then Eagle closes.

           

          What causes such error ? Any work around ?

           

          Thanks,

           

          Best regards,

           

          Jerome

           

           

          Hi Jerome,

           

          this indicates an error while calculating the polygons content.

          It is difficult to say what exactly the problem is, but you could

          try to change for example wire width of the polygon or change the

          contour slightly.

          If you don't get a solution please send me the brd file, so I will

          ty to get out what's the matter.....

           

          --

          Mit freundlichen Gruessen / Best regards

          Richard Hammerl

            CadSoft Support -- hotline@cadsoft.de

            FAQ: http://www.cadsoft.de/training/faq/

           

           

            • Re: Abort : Internal polygon error 71
              Richard_H

              Am 10.08.2011 14:07, schrieb Jerome:

              Hello,

               

              I have a large board (500x200mm) with multiple polygons for supply planes.

              At some point when I move the edges of the polygons I get a Abort :

              internal polygon error 71 message, then Eagle closes.

               

              What causes such error ? Any work around ?

               

              Thanks,

               

              Best regards,

               

              Jerome

               

               

              Hi Jerome,

               

              this indicates an error while calculating the polygons content.

              It is difficult to say what exactly the problem is, but you could

              try to change for example wire width of the polygon or change the

              contour slightly.

              If you don't get a solution please send me the brd file, so I will

              ty to get out what's the matter.....

               

              --

              Mit freundlichen Gruessen / Best regards

              Richard Hammerl

                CadSoft Support -- hotline@cadsoft.de

                FAQ: http://www.cadsoft.de/training/faq/

               

               

                • Re: Abort : Internal polygon error 71
                  jeromeabcpcb

                  "Richard Hammerl"  a écrit dans le message de groupe de discussion :

                  j1u4ht$tp5$1@cheetah.cadsoft.de...

                   

                  Am 10.08.2011 14:07, schrieb Jerome:

                  Hello,

                   

                  I have a large board (500x200mm) with multiple polygons for supply planes.

                  At some point when I move the edges of the polygons I get a Abort :

                  internal polygon error 71 message, then Eagle closes.

                   

                  What causes such error ? Any work around ?

                   

                  Thanks,

                   

                  Best regards,

                   

                  Jerome

                   

                   

                  Hi Jerome,

                   

                  this indicates an error while calculating the polygons content.

                  It is difficult to say what exactly the problem is, but you could

                  try to change for example wire width of the polygon or change the

                  contour slightly.

                  If you don't get a solution please send me the brd file, so I will

                  ty to get out what's the matter.....

                   

                  --

                  Mit freundlichen Gruessen / Best regards

                  Richard Hammerl

                    CadSoft Support -- hotline@cadsoft.de

                    FAQ: http://www.cadsoft.de/training/faq/

                   

                   

                   

                   

                   

                  Hi Richard,

                   

                  Thanks for your help.

                  I have changed the contour and after some trial and crashes, could fill the

                  area.

                   

                  Best regards,

                   

                  Jerome