19 Replies Latest reply on Aug 15, 2019 8:50 PM by khabnl

    Ultrazed-EV bootconsole [cdns0] disabled

    khabnl

      Hello,

       

      I am testing the Ultrazed-EV board and I found bootconsole [cdns0] disabled message and stopped.

       

      I added booting parameters in system-user.dtsi.

       

      bootargs = "console=ttyPS0,115200 earlycon clk_ignore_unused cpuidle.off=1 root=/dev/mmcblk0p2 rw  rootfstype=ext4 rootwait";

       

       

      U-Boot 2019.01 (Jul 19 2019 - 14:29:54 +0000)

       

      Board: Xilinx ZynqMP

      DRAM:  4 GiB

      usb dr_mode not found

      EL Level:       EL2

      Chip ID:        zu7ev

      MMC:   mmc@ff160000: 0, mmc@ff170000: 1

      Loading Environment from SPI Flash... SF: Detected n25q256a with page size 512 Bytes, erase size 128 KiB, total 64 MiB

      *** Warning - bad CRC, using default environment

       

      In:    serial@ff000000

      Out:   serial@ff000000

      Err:   serial@ff000000

      Board: Xilinx ZynqMP

      Bootmode: SD_MODE1

      Reset reason:   EXTERNAL

      Net:   ZYNQ GEM: ff0e0000, phyaddr c, interface rgmii-id

      eth0: ethernet@ff0e0000

      U-BOOT for uzev_plinux

       

      ethernet@ff0e0000 Waiting for PHY auto negotiation to complete...... done

      BOOTP broadcast 1

      BOOTP broadcast 2

      BOOTP broadcast 3

      DHCP client bound to address 192.168.0.101 (1016 ms)

      Hit any key to stop autoboot:  0

      Device: mmc@ff160000

      Manufacturer ID: 13

      OEM: 14e

      Name: Q2J55

      Bus Speed: 52000000

      Mode : MMC High Speed (52MHz)

      Rd Block Len: 512

      MMC version 5.0

      High Capacity: Yes

      Capacity: 7.1 GiB

      Bus Width: 4-bit

      Erase Group Size: 512 KiB

      HC WP Group Size: 8 MiB

      User Capacity: 7.1 GiB WRREL

      Boot Capacity: 16 MiB ENH

      RPMB Capacity: 4 MiB ENH

      23676020 bytes read in 1770 ms (12.8 MiB/s)

      ## Loading kernel from FIT Image at 10000000 ...

         Using 'conf@1' configuration

         Trying 'kernel@0' kernel subimage

           Description:  Linux Kernel

           Type:         Kernel Image

           Compression:  uncompressed

           Data Start:   0x100000d8

           Data Size:    13574656 Bytes = 12.9 MiB

           Architecture: AArch64

           OS:           Linux

           Load Address: 0x00080000

           Entry Point:  0x00080000

           Hash algo:    sha1

           Hash value:   6430bf9020db9fe81f94415ab58478ebe4154d35

         Verifying Hash Integrity ... sha1+ OK

      ## Loading ramdisk from FIT Image at 10000000 ...

         Using 'conf@1' configuration

         Trying 'ramdisk@0' ramdisk subimage

           Description:  ramdisk

           Type:         RAMDisk Image

           Compression:  uncompressed

           Data Start:   0x10cfa620

           Data Size:    10066525 Bytes = 9.6 MiB

           Architecture: AArch64

           OS:           Linux

           Load Address: unavailable

           Entry Point:  unavailable

           Hash algo:    sha1

           Hash value:   21d9aa2b62261cf1213a1643c76d418b626775cb

         Verifying Hash Integrity ... sha1+ OK

      ## Loading fdt from FIT Image at 10000000 ...

         Using 'conf@1' configuration

         Trying 'fdt@0' fdt subimage

           Description:  Flattened Device Tree blob

           Type:         Flat Device Tree

           Compression:  uncompressed

           Data Start:   0x10cf23d0

           Data Size:    33180 Bytes = 32.4 KiB

           Architecture: AArch64

           Hash algo:    sha1

           Hash value:   b128e977b259dd6ff89fe8d29afee83b6c64ac7b

         Verifying Hash Integrity ... sha1+ OK

         Booting using the fdt blob at 0x10cf23d0

         Loading Kernel Image ... OK

         Loading Ramdisk to 07666000, end 07fffa5d ... OK

         Loading Device Tree to 000000000765a000, end 000000000766519b ... OK

       

      Starting kernel ...

       

      [    0.000000] Booting Linux on physical CPU 0x0

      [    0.000000] Linux version 4.9.0-xilinx-v2017.3 (avnet@ubuv1604) (gcc version 6.2.1 20161016 (Linaro GCC 6.2-2016.11) ) #1 SMP Tue Feb 6 17:51:04 EST 2018

      [    0.000000] Boot CPU: AArch64 Processor [410fd034]

      [    0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8')

      [    0.000000] bootconsole [cdns0] enabled

      [    0.000000] efi: Getting EFI parameters from FDT:

      [    0.000000] efi: UEFI not found.

      [    0.000000] cma: Reserved 256 MiB at 0x000000006fc00000

      [    0.000000] psci: probing for conduit method from DT.

      [    0.000000] psci: PSCIv1.1 detected in firmware.

      [    0.000000] psci: Using standard PSCI v0.2 function IDs

      [    0.000000] psci: MIGRATE_INFO_TYPE not supported.

      [    0.000000] percpu: Embedded 21 pages/cpu @ffffffc87ff78000 s48152 r8192 d29672 u86016

      [    0.000000] Detected VIPT I-cache on CPU0

      [    0.000000] CPU features: enabling workaround for ARM erratum 845719

      [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 1033987

      [    0.000000] Kernel command line: earlycon clk_ignore_unused

      [    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)

      [    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)

      [    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)

      [    0.000000] software IO TLB [mem 0x6bc00000-0x6fc00000] (64MB) mapped at [ffffffc06bc00000-ffffffc06fbfffff]

      [    0.000000] Memory: 3777580K/4193280K available (9212K kernel code, 584K rwdata, 2884K rodata, 512K init, 397K bss, 153556K reserved, 262144K cma-reserved)

      [    0.000000] Virtual kernel memory layout:

      [    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)

      [    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)

      [    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008980000   (  9216 KB)

      [    0.000000]     .rodata : 0xffffff8008980000 - 0xffffff8008c60000   (  2944 KB)

      [    0.000000]       .init : 0xffffff8008c60000 - 0xffffff8008ce0000   (   512 KB)

      [    0.000000]       .data : 0xffffff8008ce0000 - 0xffffff8008d72200   (   585 KB)

      [    0.000000]        .bss : 0xffffff8008d72200 - 0xffffff8008dd5634   (   398 KB)

      [    0.000000]     fixed   : 0xffffffbefe7fd000 - 0xffffffbefec00000   (  4108 KB)

      [    0.000000]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)

      [    0.000000]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)

      [    0.000000]               0xffffffbf00000000 - 0xffffffbf1dc00000   (   476 MB actual)

      [    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc880000000   ( 34816 MB)

      [    0.000000] Hierarchical RCU implementation.

      [    0.000000]  Build-time adjustment of leaf fanout to 64.

      [    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.

      [    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4

      [    0.000000] NR_IRQS:64 nr_irqs:64 0

      [    0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000

      [    0.000000] GIC: Using split EOI/Deactivate mode

      [    0.000000] arm_arch_timer: Architected cp15 timer(s) running at 99.99MHz (phys).

      [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x171015c90f, max_idle_ns: 440795203080 ns

      [    0.000003] sched_clock: 56 bits at 99MHz, resolution 10ns, wraps every 4398046511101ns

      [    0.008221] Console: colour dummy device 80x25

      [    0.012480] console [tty0] enabled

      [    0.015846] bootconsole [cdns0] disabled

        • Re: Ultrazed-EV bootconsole [cdns0] disabled
          jafoste4

          Hi,

           

          Are you using an Avnet provided BSP?

           

          -Josh

            • Re: Ultrazed-EV bootconsole [cdns0] disabled
              khabnl

              Hi Josh,

               

              No, I create a new BOOT.bin and image.ub from the Vivado 2019.1.

               

              I had similar problem at Xilinx zcu102 board and it fixed by adding below parameter.

                     chosen {

                          bootargs = "console=ttyPS0,115200 earlycon clk_ignore_unused cpuidle.off=1 root=/dev/mmcblk0p2 rw  rootfstype=ext4 rootwait";

              stdout-path = "serial0:115200n8";

                    };

               

              But Ultrazed-EV dose not help.

               

               

              Thanks,

              Kiman

                • Re: Ultrazed-EV bootconsole [cdns0] disabled
                  zedhed

                  Hi Kiman,

                   

                  Is there a specific reason why 2019.1 is needed for your application?

                   

                  We have not done any BSP work with 2019.1 yet but we have two very stable 2018.2 BSPs posted on the UltraZed-EV page:  UltraZed-EV

                   

                   

                  I would suggest starting with one of these first before diving into 2019.1 tools as there were a lot of changes to the Xilinx tools for 2019.1 release.

                   

                  Best Regards,

                   

                  -Kevin

                    • Re: Ultrazed-EV bootconsole [cdns0] disabled
                      khabnl

                      Hi Kevin,

                       

                      Because our team switched to VV2019.1 for zynq ultrascal+ platform that's why I test with the latest petalinux,

                      But it's Okay test with petalinux 2018.2.

                       

                      I download the uz7ev_evcc_sd_oob_2018_2.bsp file for UltrascalZed-EV board test.

                       

                      I did test two step:

                      step 1 is no external rootfs    : booting fine

                      step 2 is with external rootfs  : end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,10)

                       

                       

                      My application is always configured to Root filesystem type -> SC card.

                       

                       

                      ############

                      Step 1 BSP test :

                      ############

                       

                      1) download and unzip 2018.2 bsp project

                      uz7ev_evcc_sd_oob_2018_2.bsp

                       

                      2) Creat project

                      petalinux-create -t project --template zynqMP -s uz7ev_evcc_sd_oob_2018_2.bsp -n uz7ev_evcc

                       

                       

                      3) Copy BOOT.bin and image.ub to SD card.

                      ../pre-built/linux/images

                      BOOT_SD.bin -> BOOT.bin

                      image.ub

                       

                       

                      4) SD card booting message

                      Xilinx Zynq MP First Stage Boot Loader

                      Release 2018.2   Sep  8 2018  -  01:31:09

                      NOTICE:  ATF running on XCZU7EV/silicon v4/RTL5.1 at 0xfffea000

                      NOTICE:  BL31: Secure code at 0x0

                      NOTICE:  BL31: Non secure code at 0x8000000

                      NOTICE:  BL31: v1.4(release):xilinx-v2018.1-4-g93a69a5a

                      NOTICE:  BL31: Built : 05:27:34, Sep  8 2018

                      PMUFW:  v1.0

                       

                       

                      U-Boot 2018.01 (Sep 08 2018 - 01:27:49 -0400) Xilinx ZynqMP ZCU102 rev1.0

                       

                      :

                      :

                       

                      Starting kernel ...

                       

                      [    0.000000] Booting Linux on physical CPU 0x0

                      [    0.000000] Linux version 4.14.0-xilinx-v2018.2 (oe-user@oe-host) (gcc version 7.2.0 (GCC)) #1 SMP Sat Sep 8 01:43:06 EDT 2018

                       

                      :

                      :

                       

                      root@uz7ev-evcc-sd-oob-2018-2:~# df

                      Filesystem     1K-blocks   Used Available Use% Mounted on

                      rootfs           1871852 127652   1744200   7% /

                      devtmpfs         1871852      0   1871852   0% /dev

                      tmpfs            2023532    140   2023392   1% /run

                      tmpfs            2023532     84   2023448   1% /var/volatile

                       

                       

                       

                       

                      ############

                      Step 2 BSP test for rootfs booting from Ext4:

                      ############

                       

                      1) petalinux-config

                         Change Image Packaging Configuration -> Root filesystem type -> SC card

                           

                      2) petalinux-build

                       

                      3) petalinux-package --boot --format BIN --fsbl images/linux/zynqmp_fsbl.elf --u-boot images/linux/u-boot.elf --pmufw images/linux/pmufw.elf --fpga images/linux/system.bit --force

                       

                      4) Copy BOOT.bin and image.ub to SD card

                       

                       

                      5) SD card booting message

                       

                      Xilinx Zynq MP First Stage Boot Loader

                      Release 2018.2   Jul 23 2019  -  12:08:22

                      NOTICE:  ATF running on XCZU7EV/silicon v4/RTL5.1 at 0xfffea000

                      NOTICE:  BL31: Secure code at 0x0

                      NOTICE:  BL31: Non secure code at 0x8000000

                      NOTICE:  BL31: v1.4(release):xilinx-v2018.1-4-g93a69a5a

                      NOTICE:  BL31: Built : 16:06:08, Jul 23 2019

                      PMUFW:  v1.0

                       

                       

                      U-Boot 2018.01 (Jul 23 2019 - 12:06:10 -0400) Xilinx ZynqMP ZCU102 rev1.0

                       

                       

                      Starting kernel ...

                       

                      [    0.000000] Booting Linux on physical CPU 0x0

                      [    0.000000] Linux version 4.14.0-xilinx-v2018.2 (oe-user@oe-host) (gcc version 7.2.0 (GCC)) #1 SMP Tue Jul 23 12:14:41 EDT 2019

                      :

                      :

                      :

                       

                      [    3.760906] rtc_zynqmp ffa60000.rtc: setting system clock to 2038-01-22 04:37:01 UTC (2147747821)

                      [    3.769816] clk: Not disabling unused clocks

                      [    3.774050] ALSA device list:

                      [    3.776960]   #0: DisplayPort monitor

                      [    3.781065] VFS: Cannot open root device "mmcblk0p2" or unknown-block(179,10): error -6

                      [    3.789000] Please append a correct "root=" boot option; here are the available partitions:

                      [    3.797331] 0100           65536 ram0

                      [    3.797333]  (driver?)

                      [    3.803395] 0101           65536 ram1

                      [    3.803396]  (driver?)

                      [    3.809475] 0102           65536 ram2

                      [    3.809477]  (driver?)

                      [    3.815546] 0103           65536 ram3

                      [    3.815548]  (driver?)

                      [    3.821626] 0104           65536 ram4

                      [    3.821628]  (driver?)

                      [    3.827698] 0105           65536 ram5

                      [    3.827699]  (driver?)

                      [    3.833778] 0106           65536 ram6

                      [    3.833780]  (driver?)

                      [    3.839850] 0107           65536 ram7

                      [    3.839852]  (driver?)

                      [    3.845930] 0108           65536 ram8

                      [    3.845932]  (driver?)

                      [    3.852002] 0109           65536 ram9

                      [    3.852004]  (driver?)

                      [    3.858083] 010a           65536 ram10

                      [    3.858084]  (driver?)

                      [    3.864241] 010b           65536 ram11

                      [    3.864243]  (driver?)

                      [    3.870408] 010c           65536 ram12

                      [    3.870410]  (driver?)

                      [    3.876567] 010d           65536 ram13

                      [    3.876568]  (driver?)

                      [    3.882734] 010e           65536 ram14

                      [    3.882736]  (driver?)

                      [    3.888893] 010f           65536 ram15

                      [    3.888894]  (driver?)

                      [    3.895062] 1f00           19840 mtdblock0

                      [    3.895064]  (driver?)

                      [    3.901570] 1f01             256 mtdblock1

                      [    3.901572]  (driver?)

                      [    3.908076] 1f02           23552 mtdblock2

                      [    3.908077]  (driver?)

                      [    3.914590] b300        30547968 mmcblk1

                      [    3.914592]  driver: mmcblk

                      [    3.921362]   b301         1047552 mmcblk1p1 561ae528-01

                      [    3.921363]

                      [    3.928126]   b302        29499392 mmcblk1p2 561ae528-02

                      [    3.928128]

                      [    3.934897] b308         7438336 mmcblk0

                      [    3.934899]  driver: mmcblk

                      [    3.941672]   b309          250040 mmcblk0p1 00000000-01

                      [    3.941674]

                      [    3.948438] b320            4096 mmcblk0rpmb

                      [    3.948440]  (driver?)

                      [    3.955126] b318           16384 mmcblk0boot1

                      [    3.955128]  (driver?)

                      [    3.961897] b310           16384 mmcblk0boot0

                      [    3.961898]  (driver?)

                      [    3.968662] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,10)

                      [    3.977174] CPU: 3 PID: 1 Comm: swapper/0 Not tainted 4.14.0-xilinx-v2018.2 #1

                      [    3.984375] Hardware name: xlnx,zynqmp (DT)

                      [    3.988539] Call trace:

                      [    3.990976] [<ffffff8008088c58>] dump_backtrace+0x0/0x368

                      [    3.996355] [<ffffff8008088fd4>] show_stack+0x14/0x20

                      [    4.001389] [<ffffff8008a361f8>] dump_stack+0x9c/0xbc

                      [    4.006424] [<ffffff800809bdc0>] panic+0x11c/0x274

                      [    4.011198] [<ffffff8008d81124>] mount_block_root+0x1a8/0x27c

                      [    4.016926] [<ffffff8008d81430>] mount_root+0x11c/0x134

                      [    4.022133] [<ffffff8008d815b4>] prepare_namespace+0x16c/0x1b4

                      [    4.027949] [<ffffff8008d80d44>] kernel_init_freeable+0x1b8/0x1d8

                      [    4.034026] [<ffffff8008a48560>] kernel_init+0x10/0x100

                      [    4.039233] [<ffffff8008084a90>] ret_from_fork+0x10/0x18

                      [    4.044527] SMP: stopping secondary CPUs

                      [    4.048433] Kernel Offset: disabled

                      [    4.051904] CPU features: 0x002004

                      [    4.055288] Memory Limit: none

                      [    4.058330] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,10)

                        • Re: Ultrazed-EV bootconsole [cdns0] disabled
                          zedhed

                          Hi Kiman,

                           

                          Thanks for posting the steps you followed, that makes it much easier to understand where you are getting stuck.

                           

                          I do not see any instructions that you've listed for extracting the ROOTFS to the external file system.  Usually, this is done by creating a second EXT4 partition on the SD card like this:

                           

                           

                          Once you have the second partition in place, you can extract the packed ROOTFS tarball from PetaLinux to this partition.  When Linux boots on UltraZed, it will attempt to mount the EXT4 partition on the SD card and use its contents as the persistent root filesystem.

                           

                           

                          Further details are available for you in the Xilinx UG1144 reference guide:

                           

                          https://www.xilinx.com/support/documentation/sw_manuals/xilinx2018_2/ug1144-petalinux-tools-reference-guide.pdf

                           

                          Best Regards,

                           

                          -Kevin

                            • Re: Ultrazed-EV bootconsole [cdns0] disabled
                              khabnl

                              Hi Kevin,

                               

                              Thank you for the update.

                              My case I am using Debian 9 and Debian 10 instead of the petalinux rootfs.

                               

                               

                              Xilinx Zynq MP First Stage Boot Loader

                              Release 2018.2   Jul 23 2019  -  12:08:22

                              NOTICE:  ATF running on XCZU7EV/silicon v4/RTL5.1 at 0xfffea000

                              NOTICE:  BL31: Secure code at 0x0

                              NOTICE:  BL31: Non secure code at 0x8000000

                              NOTICE:  BL31: v1.4(release):xilinx-v2018.1-4-g93a69a5a

                              NOTICE:  BL31: Built : 16:06:08, Jul 23 2019

                              PMUFW:  v1.0

                               

                               

                              U-Boot 2018.01 (Jul 23 2019 - 12:06:10 -0400) Xilinx ZynqMP ZCU102 rev1.0

                               

                              I2C:   ready

                              DRAM:  4 GiB

                              EL Level:       EL2

                              Chip ID:        zu7ev

                              MMC:   sdhci@ff160000: 0 (eMMC), sdhci@ff170000: 1 (SD)

                              SF: Detected n25q256a with page size 512 Bytes, erase size 128 KiB, total 64 MiB

                              In:    serial@ff000000

                              Out:   serial@ff000000

                              Err:   serial@ff000000

                              Board: Xilinx ZynqMP

                              Net:   ZYNQ GEM: ff0e0000, phyaddr 0, interface rgmii-id

                              eth0: ethernet@ff0e0000

                              Hit any key to stop autoboot:  0

                              Device: sdhci@ff160000

                              Manufacturer ID: 13

                              OEM: 14e

                              Name: Q2J55

                              Tran Speed: 200000000

                              Rd Block Len: 512

                              MMC version 5.0

                              High Capacity: Yes

                              Capacity: 7.1 GiB

                              Bus Width: 4-bit

                              Erase Group Size: 512 KiB

                              HC WP Group Size: 8 MiB

                              User Capacity: 7.1 GiB WRREL

                              Boot Capacity: 16 MiB ENH

                              RPMB Capacity: 4 MiB ENH

                              reading image.ub

                              7077104 bytes read in 495 ms (13.6 MiB/s)

                              ## Loading kernel from FIT Image at 10000000 ...

                                 Using 'conf@system-top.dtb' configuration

                                 Trying 'kernel@1' kernel subimage

                                   Description:  Linux kernel

                                   Type:         Kernel Image

                                   Compression:  gzip compressed

                                   Data Start:   0x10000104

                                   Data Size:    7041634 Bytes = 6.7 MiB

                                   Architecture: AArch64

                                   OS:           Linux

                                   Load Address: 0x00080000

                                   Entry Point:  0x00080000

                                   Hash algo:    sha1

                                   Hash value:   4e3656b5969723c6718bef2254f7f7c48b779b2d

                                 Verifying Hash Integrity ... sha1+ OK

                              ## Loading fdt from FIT Image at 10000000 ...

                                 Using 'conf@system-top.dtb' configuration

                                 Trying 'fdt@system-top.dtb' fdt subimage

                                   Description:  Flattened Device Tree blob

                                   Type:         Flat Device Tree

                                   Compression:  uncompressed

                                   Data Start:   0x106b746c

                                   Data Size:    33552 Bytes = 32.8 KiB

                                   Architecture: AArch64

                                   Hash algo:    sha1

                                   Hash value:   588c99069ec123cbb3b7a6caf824ece430d39761

                                 Verifying Hash Integrity ... sha1+ OK

                                 Booting using the fdt blob at 0x106b746c

                                 Uncompressing Kernel Image ... OK

                                 Loading Device Tree to 0000000007ff4000, end 0000000007fff30f ... OK

                               

                              Starting kernel ...

                               

                              [    0.000000] Booting Linux on physical CPU 0x0

                              [    0.000000] Linux version 4.14.0-xilinx-v2018.2 (oe-user@oe-host) (gcc version 7.2.0 (GCC)) #1 SMP Tue Jul 23 12:14:41 EDT 2019

                              [    0.000000] Boot CPU: AArch64 Processor [410fd034]

                              [    0.000000] Machine model: xlnx,zynqmp

                              [    0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8')

                              [    0.000000] bootconsole [cdns0] enabled

                              [    0.000000] efi: Getting EFI parameters from FDT:

                              [    0.000000] efi: UEFI not found.

                              [    0.000000] cma: Reserved 256 MiB at 0x000000006fc00000

                              [    0.000000] psci: probing for conduit method from DT.

                              [    0.000000] psci: PSCIv1.1 detected in firmware.

                              [    0.000000] psci: Using standard PSCI v0.2 function IDs

                              [    0.000000] psci: MIGRATE_INFO_TYPE not supported.

                              [    0.000000] percpu: Embedded 21 pages/cpu @ffffffc87ff76000 s46488 r8192 d31336 u86016

                              [    0.000000] Detected VIPT I-cache on CPU0

                              [    0.000000] CPU features: enabling workaround for ARM erratum 845719

                              [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1033987

                              [    0.000000] Kernel command line: earlycon clk_ignore_unused root=/dev/mmcblk1p2 rw rootwait

                              [    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)

                              [    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)

                              [    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)

                              [    0.000000] software IO TLB [mem 0x6bc00000-0x6fc00000] (64MB) mapped at [ffffffc06bc00000-ffffffc06fbfffff]

                              [    0.000000] Memory: 3784416K/4193280K available (10108K kernel code, 646K rwdata, 3148K rodata, 512K init, 2166K bss, 146720K reserved, 262144K cma-reserved)

                              [    0.000000] Virtual kernel memory layout:

                              [    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)

                              [    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)

                              [    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008a60000   ( 10112 KB)

                              [    0.000000]     .rodata : 0xffffff8008a60000 - 0xffffff8008d80000   (  3200 KB)

                              [    0.000000]       .init : 0xffffff8008d80000 - 0xffffff8008e00000   (   512 KB)

                              [    0.000000]       .data : 0xffffff8008e00000 - 0xffffff8008ea1a00   (   647 KB)

                              [    0.000000]        .bss : 0xffffff8008ea1a00 - 0xffffff80090bf2b0   (  2167 KB)

                              [    0.000000]     fixed   : 0xffffffbefe7fd000 - 0xffffffbefec00000   (  4108 KB)

                              [    0.000000]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)

                              [    0.000000]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)

                              [    0.000000]               0xffffffbf00000000 - 0xffffffbf1dc00000   (   476 MB actual)

                              [    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc880000000   ( 34816 MB)

                              [    0.000000] Hierarchical RCU implementation.

                              [    0.000000]  RCU event tracing is enabled.

                              [    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.

                              [    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4

                              [    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0

                              [    0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000

                              [    0.000000] GIC: Using split EOI/Deactivate mode

                              [    0.000000] arch_timer: cp15 timer(s) running at 99.99MHz (phys).

                              [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x171015c90f, max_idle_ns: 440795203080 ns

                              [    0.000003] sched_clock: 56 bits at 99MHz, resolution 10ns, wraps every 4398046511101ns

                              [    0.008259] Console: colour dummy device 80x25

                              [    0.012516] console [tty0] enabled

                              [    0.015882] bootconsole [cdns0] disabled

                              [    0.000000] Booting Linux on physical CPU 0x0

                              [    0.000000] Linux version 4.14.0-xilinx-v2018.2 (oe-user@oe-host) (gcc version 7.2.0 (GCC)) #1 SMP Tue Jul 23 12:14:41 EDT 2019

                              [    0.000000] Boot CPU: AArch64 Processor [410fd034]

                              [    0.000000] Machine model: xlnx,zynqmp

                              [    0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8')

                              [    0.000000] bootconsole [cdns0] enabled

                              [    0.000000] efi: Getting EFI parameters from FDT:

                              [    0.000000] efi: UEFI not found.

                              [    0.000000] cma: Reserved 256 MiB at 0x000000006fc00000

                              [    0.000000] psci: probing for conduit method from DT.

                              [    0.000000] psci: PSCIv1.1 detected in firmware.

                              [    0.000000] psci: Using standard PSCI v0.2 function IDs

                              [    0.000000] psci: MIGRATE_INFO_TYPE not supported.

                              [    0.000000] percpu: Embedded 21 pages/cpu @ffffffc87ff76000 s46488 r8192 d31336 u86016

                              [    0.000000] Detected VIPT I-cache on CPU0

                              [    0.000000] CPU features: enabling workaround for ARM erratum 845719

                              [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1033987

                              [    0.000000] Kernel command line: earlycon clk_ignore_unused root=/dev/mmcblk1p2 rw rootwait

                              [    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)

                              [    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)

                              [    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)

                              [    0.000000] software IO TLB [mem 0x6bc00000-0x6fc00000] (64MB) mapped at [ffffffc06bc00000-ffffffc06fbfffff]

                              [    0.000000] Memory: 3784416K/4193280K available (10108K kernel code, 646K rwdata, 3148K rodata, 512K init, 2166K bss, 146720K reserved, 262144K cma-reserved)

                              [    0.000000] Virtual kernel memory layout:

                              [    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)

                              [    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)

                              [    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008a60000   ( 10112 KB)

                              [    0.000000]     .rodata : 0xffffff8008a60000 - 0xffffff8008d80000   (  3200 KB)

                              [    0.000000]       .init : 0xffffff8008d80000 - 0xffffff8008e00000   (   512 KB)

                              [    0.000000]       .data : 0xffffff8008e00000 - 0xffffff8008ea1a00   (   647 KB)

                              [    0.000000]        .bss : 0xffffff8008ea1a00 - 0xffffff80090bf2b0   (  2167 KB)

                              [    0.000000]     fixed   : 0xffffffbefe7fd000 - 0xffffffbefec00000   (  4108 KB)

                              [    0.000000]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)

                              [    0.000000]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)

                              [    0.000000]               0xffffffbf00000000 - 0xffffffbf1dc00000   (   476 MB actual)

                              [    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc880000000   ( 34816 MB)

                              [    0.000000] Hierarchical RCU implementation.

                              [    0.000000]  RCU event tracing is enabled.

                              [    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.

                              [    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4

                              [    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0

                              [    0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000

                              [    0.000000] GIC: Using split EOI/Deactivate mode

                              [    0.000000] arch_timer: cp15 timer(s) running at 99.99MHz (phys).

                              [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x171015c90f, max_idle_ns: 440795203080 ns

                              [    0.000003] sched_clock: 56 bits at 99MHz, resolution 10ns, wraps every 4398046511101ns

                              [    0.008259] Console: colour dummy device 80x25

                              [    0.012516] console [tty0] enabled

                              [    0.015882] bootconsole [cdns0] disabled

                              [    0.019792] Calibrating delay loop (skipped), value calculated using timer frequency.. 199.99 BogoMIPS (lpj=399996)

                              [    0.019807] pid_max: default: 32768 minimum: 301

                              [    0.019914] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)

                              [    0.019932] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)

                              [    0.020520] ASID allocator initialised with 65536 entries

                              [    0.020572] Hierarchical SRCU implementation.

                              [    0.020872] EFI services will not be available.

                              [    0.020899] zynqmp_plat_init Platform Management API v1.0

                              [    0.020908] zynqmp_plat_init Trustzone version v1.0

                              [    0.021011] smp: Bringing up secondary CPUs ...

                              [    0.021280] Detected VIPT I-cache on CPU1

                              [    0.021310] CPU1: Booted secondary processor [410fd034]

                              [    0.021603] Detected VIPT I-cache on CPU2

                              [    0.021622] CPU2: Booted secondary processor [410fd034]

                              [    0.021903] Detected VIPT I-cache on CPU3

                              [    0.021922] CPU3: Booted secondary processor [410fd034]

                              [    0.021967] smp: Brought up 1 node, 4 CPUs

                              [    0.022001] SMP: Total of 4 processors activated.

                              [    0.022010] CPU features: detected feature: 32-bit EL0 Support

                              [    0.022022] CPU: All CPU(s) started at EL2

                              [    0.022039] alternatives: patching kernel code

                              [    0.022774] devtmpfs: initialized

                              [    0.026399] random: get_random_u32 called from bucket_table_alloc+0x108/0x260 with crng_init=0

                              [    0.026612] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns

                              [    0.026635] futex hash table entries: 1024 (order: 5, 131072 bytes)

                              [    0.026850] random: fast init done

                              [    0.032505] xor: measuring software checksum speed

                              [    0.071867]    8regs     :  2111.000 MB/sec

                              [    0.111900]    8regs_prefetch:  1882.000 MB/sec

                              [    0.151930]    32regs    :  2594.000 MB/sec

                              [    0.191964]    32regs_prefetch:  2183.000 MB/sec

                              [    0.191972] xor: using function: 32regs (2594.000 MB/sec)

                              [    0.192041] pinctrl core: initialized pinctrl subsystem

                              [    0.192571] NET: Registered protocol family 16

                              [    0.193257] cpuidle: using governor menu

                              [    0.193650] vdso: 2 pages (1 code @ ffffff8008a66000, 1 data @ ffffff8008e04000)

                              [    0.193668] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.

                              [    0.194154] DMA: preallocated 256 KiB pool for atomic allocations

                              [    0.224773] reset_zynqmp reset-controller: Xilinx zynqmp reset driver probed

                              [    0.225280] ARM CCI_400_r1 PMU driver probed

                              [    0.230508] zynqmp-pinctrl ff180000.pinctrl: zynqmp pinctrl initialized

                              [    0.238488] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages

                              [    0.304142] raid6: int64x1  gen()   369 MB/s

                              [    0.372170] raid6: int64x1  xor()   409 MB/s

                              [    0.440210] raid6: int64x2  gen()   630 MB/s

                              [    0.508301] raid6: int64x2  xor()   553 MB/s

                              [    0.576315] raid6: int64x4  gen()   956 MB/s

                              [    0.644373] raid6: int64x4  xor()   680 MB/s

                              [    0.712444] raid6: int64x8  gen()   898 MB/s

                              [    0.780494] raid6: int64x8  xor()   683 MB/s

                              [    0.848611] raid6: neonx1   gen()   666 MB/s

                              [    0.916591] raid6: neonx1   xor()   781 MB/s

                              [    0.984679] raid6: neonx2   gen()  1072 MB/s

                              [    1.052720] raid6: neonx2   xor()  1106 MB/s

                              [    1.120801] raid6: neonx4   gen()  1380 MB/s

                              [    1.188836] raid6: neonx4   xor()  1321 MB/s

                              [    1.256891] raid6: neonx8   gen()  1513 MB/s

                              [    1.324940] raid6: neonx8   xor()  1405 MB/s

                              [    1.324949] raid6: using algorithm neonx8 gen() 1513 MB/s

                              [    1.324957] raid6: .... xor() 1405 MB/s, rmw enabled

                              [    1.324965] raid6: using neon recovery algorithm

                              [    1.325554] XGpio: /amba_pl@0/gpio@a0000000: registered, base is 504

                              [    1.325877] XGpio: /amba_pl@0/gpio@a0001000: registered, base is 496

                              [    1.326116] XGpio: /amba_pl@0/gpio@a0002000: registered, base is 493

                              [    1.326897] SCSI subsystem initialized

                              [    1.327075] usbcore: registered new interface driver usbfs

                              [    1.327115] usbcore: registered new interface driver hub

                              [    1.327154] usbcore: registered new device driver usb

                              [    1.327219] media: Linux media interface: v0.10

                              [    1.327248] Linux video capture interface: v2.00

                              [    1.327295] pps_core: LinuxPPS API ver. 1 registered

                              [    1.327304] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>

                              [    1.327326] PTP clock support registered

                              [    1.327351] EDAC MC: Ver: 3.0.0

                              [    1.327652] zynqmp-ipi ff9905c0.mailbox: Probed ZynqMP IPI Mailbox driver.

                              [    1.327801] FPGA manager framework

                              [    1.327916] fpga-region fpga-full: FPGA Region probed

                              [    1.328015] Advanced Linux Sound Architecture Driver Initialized.

                              [    1.328275] Bluetooth: Core ver 2.22

                              [    1.328307] NET: Registered protocol family 31

                              [    1.328315] Bluetooth: HCI device and connection manager initialized

                              [    1.328328] Bluetooth: HCI socket layer initialized

                              [    1.328338] Bluetooth: L2CAP socket layer initialized

                              [    1.328356] Bluetooth: SCO socket layer initialized

                              [    1.328877] clocksource: Switched to clocksource arch_sys_counter

                              [    1.328952] VFS: Disk quotas dquot_6.6.0

                              [    1.329003] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)

                              [    1.333330] NET: Registered protocol family 2

                              [    1.333635] TCP established hash table entries: 32768 (order: 6, 262144 bytes)

                              [    1.333864] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)

                              [    1.334289] TCP: Hash tables configured (established 32768 bind 32768)

                              [    1.334359] UDP hash table entries: 2048 (order: 4, 65536 bytes)

                              [    1.334444] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)

                              [    1.334604] NET: Registered protocol family 1

                              [    1.334789] RPC: Registered named UNIX socket transport module.

                              [    1.334799] RPC: Registered udp transport module.

                              [    1.334807] RPC: Registered tcp transport module.

                              [    1.334815] RPC: Registered tcp NFSv4.1 backchannel transport module.

                              [    1.335241] hw perfevents: no interrupt-affinity property for /pmu, guessing.

                              [    1.335400] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available

                              [    1.336073] audit: initializing netlink subsys (disabled)

                              [    1.336453] audit: type=2000 audit(1.316:1): state=initialized audit_enabled=0 res=1

                              [    1.336496] workingset: timestamp_bits=62 max_order=20 bucket_order=0

                              [    1.337251] NFS: Registering the id_resolver key type

                              [    1.337273] Key type id_resolver registered

                              [    1.337282] Key type id_legacy registered

                              [    1.337295] nfs4filelayout_init: NFSv4 File Layout Driver Registering...

                              [    1.337317] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.

                              [    1.362958] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)

                              [    1.362975] io scheduler noop registered

                              [    1.362983] io scheduler deadline registered

                              [    1.363006] io scheduler cfq registered (default)

                              [    1.363015] io scheduler mq-deadline registered

                              [    1.363023] io scheduler kyber registered

                              [    1.363623] nwl-pcie fd0e0000.pcie: Link is DOWN

                              [    1.363668] OF: PCI: host bridge /amba/pcie@fd0e0000 ranges:

                              [    1.363690] OF: PCI:   MEM 0xe0000000..0xefffffff -> 0xe0000000

                              [    1.363703] OF: PCI:   MEM 0x600000000..0x7ffffffff -> 0x600000000

                              [    1.363835] nwl-pcie fd0e0000.pcie: PCI host bridge to bus 0000:00

                              [    1.363850] pci_bus 0000:00: root bus resource [bus 00-ff]

                              [    1.363861] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]

                              [    1.363873] pci_bus 0000:00: root bus resource [mem 0x600000000-0x7ffffffff pref]

                              [    1.364144] pci 0000:00:00.0: PCI bridge to [bus 01-0c]

                              [    1.365012] xilinx-dpdma fd4c0000.dma: Xilinx DPDMA engine is probed

                              [    1.365405] xilinx-zynqmp-dma fd500000.dma: ZynqMP DMA driver Probe success

                              [    1.365564] xilinx-zynqmp-dma fd510000.dma: ZynqMP DMA driver Probe success

                              [    1.365717] xilinx-zynqmp-dma fd520000.dma: ZynqMP DMA driver Probe success

                              [    1.365871] xilinx-zynqmp-dma fd530000.dma: ZynqMP DMA driver Probe success

                              [    1.366025] xilinx-zynqmp-dma fd540000.dma: ZynqMP DMA driver Probe success

                              [    1.366179] xilinx-zynqmp-dma fd550000.dma: ZynqMP DMA driver Probe success

                              [    1.366336] xilinx-zynqmp-dma fd560000.dma: ZynqMP DMA driver Probe success

                              [    1.366493] xilinx-zynqmp-dma fd570000.dma: ZynqMP DMA driver Probe success

                              [    1.366721] xilinx-zynqmp-dma ffa80000.dma: ZynqMP DMA driver Probe success

                              [    1.366874] xilinx-zynqmp-dma ffa90000.dma: ZynqMP DMA driver Probe success

                              [    1.367029] xilinx-zynqmp-dma ffaa0000.dma: ZynqMP DMA driver Probe success

                              [    1.367185] xilinx-zynqmp-dma ffab0000.dma: ZynqMP DMA driver Probe success

                              [    1.367338] xilinx-zynqmp-dma ffac0000.dma: ZynqMP DMA driver Probe success

                              [    1.367492] xilinx-zynqmp-dma ffad0000.dma: ZynqMP DMA driver Probe success

                              [    1.367645] xilinx-zynqmp-dma ffae0000.dma: ZynqMP DMA driver Probe success

                              [    1.367799] xilinx-zynqmp-dma ffaf0000.dma: ZynqMP DMA driver Probe success

                              [    1.394864] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled

                              [    1.398145] cacheinfo: Unable to detect cache hierarchy for CPU 0

                              [    1.402489] brd: module loaded

                              [    1.405941] loop: module loaded

                              [    1.406882] ahci-ceva fd0c0000.ahci: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl platform mode

                              [    1.406902] ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst

                              [    1.407648] scsi host0: ahci-ceva

                              [    1.407951] scsi host1: ahci-ceva

                              [    1.408072] ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 43

                              [    1.408086] ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 43

                              [    1.408245] mtdoops: mtd device (mtddev=name/number) must be supplied

                              [    1.409103] m25p80 spi0.0: found n25q256a, expected m25p80

                              [    1.409365] m25p80 spi0.0: n25q256a (65536 Kbytes)

                              [    1.409387] 3 ofpart partitions found on MTD device spi0.0

                              [    1.409396] Creating 3 MTD partitions on "spi0.0":

                              [    1.409408] 0x000000000000-0x000001360000 : "boot"

                              [    1.409874] 0x000001360000-0x0000013a0000 : "bootenv"

                              [    1.410277] 0x0000013a0000-0x000002aa0000 : "kernel"

                              [    1.411589] libphy: Fixed MDIO Bus: probed

                              [    1.412701] tun: Universal TUN/TAP device driver, 1.6

                              [    1.412827] CAN device driver interface

                              [    1.413486] macb ff0e0000.ethernet: Not enabling partial store and forward

                              [    1.413941] libphy: MACB_mii_bus: probed

                              [    1.485106] macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000 irq 30 (00:0a:35:00:22:01)

                              [    1.485125] Marvell 88E1510 ff0e0000.ethernet-ffffffff:00: attached PHY driver [Marvell 88E1510] (mii_bus:phy_addr=ff0e0000.ethernet-ffffffff:00, irq=POLL)

                              [    1.485748] usbcore: registered new interface driver asix

                              [    1.485802] usbcore: registered new interface driver ax88179_178a

                              [    1.485837] usbcore: registered new interface driver cdc_ether

                              [    1.485869] usbcore: registered new interface driver net1080

                              [    1.485902] usbcore: registered new interface driver cdc_subset

                              [    1.485933] usbcore: registered new interface driver zaurus

                              [    1.485976] usbcore: registered new interface driver cdc_ncm

                              [    1.486258] xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM

                              [    1.486617] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

                              [    1.486628] ehci-pci: EHCI PCI platform driver

                              [    1.486901] usbcore: registered new interface driver cdc_acm

                              [    1.486911] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters

                              [    1.486945] usbcore: registered new interface driver uas

                              [    1.486985] usbcore: registered new interface driver usb-storage

                              [    1.487473] rtc_zynqmp ffa60000.rtc: rtc core: registered ffa60000.rtc as rtc0

                              [    1.487530] i2c /dev entries driver

                              [    1.487961] cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 32

                              [    1.542340] i2c i2c-0: Added multiplexed i2c bus 1

                              [    1.542469] i2c i2c-0: Added multiplexed i2c bus 2

                              [    1.542481] pca954x 0-0070: registered 2 multiplexed busses for I2C mux pca9542

                              [    1.542583] IR NEC protocol handler initialized

                              [    1.542592] IR RC5(x/sz) protocol handler initialized

                              [    1.542600] IR RC6 protocol handler initialized

                              [    1.542608] IR JVC protocol handler initialized

                              [    1.542615] IR Sony protocol handler initialized

                              [    1.542623] IR SANYO protocol handler initialized

                              [    1.542631] IR Sharp protocol handler initialized

                              [    1.542638] IR MCE Keyboard/mouse protocol handler initialized

                              [    1.542646] IR XMP protocol handler initialized

                              [    1.543722] usbcore: registered new interface driver uvcvideo

                              [    1.543732] USB Video Class driver (1.1.1)

                              [    1.544242] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer at ffffff8009175000 with timeout 10s

                              [    1.544429] Bluetooth: HCI UART driver ver 2.3

                              [    1.544440] Bluetooth: HCI UART protocol H4 registered

                              [    1.544448] Bluetooth: HCI UART protocol BCSP registered

                              [    1.544477] Bluetooth: HCI UART protocol LL registered

                              [    1.544486] Bluetooth: HCI UART protocol ATH3K registered

                              [    1.544495] Bluetooth: HCI UART protocol Three-wire (H5) registered

                              [    1.544542] Bluetooth: HCI UART protocol Intel registered

                              [    1.544551] Bluetooth: HCI UART protocol QCA registered

                              [    1.544590] usbcore: registered new interface driver bcm203x

                              [    1.544626] usbcore: registered new interface driver bpa10x

                              [    1.544662] usbcore: registered new interface driver bfusb

                              [    1.544699] usbcore: registered new interface driver btusb

                              [    1.544709] Bluetooth: Generic Bluetooth SDIO driver ver 0.1

                              [    1.544761] usbcore: registered new interface driver ath3k

                              [    1.544911] EDAC MC: ECC not enabled

                              [    1.545115] EDAC DEVICE0: Giving out device to module zynqmp-ocm-edac controller zynqmp_ocm: DEV ff960000.memory-controller (INTERRUPT)

                              [    1.545591] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 1099999 KHz

                              [    1.545648] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1199999 KHz

                              [    1.546049] sdhci: Secure Digital Host Controller Interface driver

                              [    1.546059] sdhci: Copyright(c) Pierre Ossman

                              [    1.546067] sdhci-pltfm: SDHCI platform and OF driver helper

                              [    1.589009] mmc0: SDHCI controller on ff160000.sdhci [ff160000.sdhci] using ADMA 64-bit

                              [    1.589069] PLL: shutdown

                              [    1.589155] PLL: enable

                              [    1.636886] mmc1: SDHCI controller on ff170000.sdhci [ff170000.sdhci] using ADMA 64-bit

                              [    1.642856] ledtrig-cpu: registered to indicate activity on CPUs

                              [    1.643006] usbcore: registered new interface driver usbhid

                              [    1.643015] usbhid: USB HID core driver

                              [    1.644902] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered

                              [    1.645667] pktgen: Packet Generator for packet performance testing. Version: 2.75

                              [    1.645967] Netfilter messages via NETLINK v0.30.

                              [    1.646089] ip_tables: (C) 2000-2006 Netfilter Core Team

                              [    1.650488] Initializing XFRM netlink socket

                              [    1.650553] NET: Registered protocol family 10

                              [    1.651981] Segment Routing with IPv6

                              [    1.652030] ip6_tables: (C) 2000-2006 Netfilter Core Team

                              [    1.653185] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver

                              [    1.653524] NET: Registered protocol family 17

                              [    1.653541] NET: Registered protocol family 15

                              [    1.653561] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.

                              [    1.653576] Ebtables v2.0 registered

                              [    1.653686] can: controller area network core (rev 20170425 abi 9)

                              [    1.653724] NET: Registered protocol family 29

                              [    1.653734] can: raw protocol (rev 20170425)

                              [    1.653743] can: broadcast manager protocol (rev 20170425 t)

                              [    1.653754] can: netlink gateway (rev 20170425) max_hops=1

                              [    1.653821] Bluetooth: RFCOMM TTY layer initialized

                              [    1.653833] Bluetooth: RFCOMM socket layer initialized

                              [    1.653848] Bluetooth: RFCOMM ver 1.11

                              [    1.653859] Bluetooth: BNEP (Ethernet Emulation) ver 1.3

                              [    1.653868] Bluetooth: BNEP filters: protocol multicast

                              [    1.653878] Bluetooth: BNEP socket layer initialized

                              [    1.653887] Bluetooth: HIDP (Human Interface Emulation) ver 1.2

                              [    1.653897] Bluetooth: HIDP socket layer initialized

                              [    1.654013] 9pnet: Installing 9P2000 support

                              [    1.654033] Key type dns_resolver registered

                              [    1.654425] registered taskstats version 1

                              [    1.654751] Btrfs loaded, crc32c=crc32c-generic

                              [    1.659953] ff000000.serial: ttyPS0 at MMIO 0xff000000 (irq = 46, base_baud = 6249999) is a xuartps

                              [    1.723143] ata2: SATA link down (SStatus 0 SControl 330)

                              [    1.723178] ata1: SATA link down (SStatus 0 SControl 330)

                              [    1.826745] mmc1: Problem switching card into high-speed mode!

                              [    1.841361] mmc1: new SDHC card at address 0001

                              [    1.843588] mmcblk1: mmc1:0001 Team 29.1 GiB

                              [    1.851116]  mmcblk1: p1 p2

                              [    1.851282] mmc0: new HS200 MMC card at address 0001

                              [    1.851660] mmcblk0: mmc0:0001 Q2J55L 7.09 GiB

                              [    1.858945] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 16.0 MiB

                              [    1.866236] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 16.0 MiB

                              [    1.873522] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB

                              [    1.880971]  mmcblk0: p1

                              [    3.455782] console [ttyPS0] enabled

                              [    3.459797] ff010000.serial: ttyPS1 at MMIO 0xff010000 (irq = 47, base_baud = 6249999) is a xuartps

                              [    3.469943] xilinx-psgtr fd400000.zynqmp_phy: Lane:3 type:8 protocol:4 pll_locked:yes

                              [    3.478112] PLL: shutdown

                              [    3.482257] xilinx-dp-snd-codec fd4a0000.zynqmp-display:zynqmp_dp_snd_codec0: Xilinx DisplayPort Sound Codec probed

                              [    3.492847] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm0: Xilinx DisplayPort Sound PCM probed

                              [    3.500808] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm1: Xilinx DisplayPort Sound PCM probed

                              [    3.509069] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: xilinx-dp-snd-codec-dai <-> xilinx-dp-snd-codec-dai mapping ok

                              [    3.521433] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: xilinx-dp-snd-codec-dai <-> xilinx-dp-snd-codec-dai mapping ok

                              [    3.534063] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: Xilinx DisplayPort Sound Card probed

                              [    3.544166] OF: graph: no port node found in /amba/zynqmp-display@fd4a0000

                              [    3.551095] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).

                              [    3.557629] [drm] No driver support for vblank timestamp query.

                              [    3.563593] xlnx-drm xlnx-drm.0: bound fd4a0000.zynqmp-display (ops 0xffffff8008b17228)

                              [    3.602303] [drm] Cannot find any crtc or sizes

                              [    3.606933] [drm] Initialized xlnx 1.0.0 20130509 for fd4a0000.zynqmp-display on minor 0

                              [    3.614964] zynqmp-display fd4a0000.zynqmp-display: ZynqMP DisplayPort Subsystem driver probed

                              [    3.624429] xilinx-psgtr fd400000.zynqmp_phy: Lane:2 type:0 protocol:3 pll_locked:yes

                              [    3.634396] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller

                              [    3.639811] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1

                              [    3.647655] xhci-hcd xhci-hcd.0.auto: hcc params 0x0238f625 hci version 0x100 quirks 0x22010010

                              [    3.656309] xhci-hcd xhci-hcd.0.auto: irq 71, io mem 0xfe200000

                              [    3.662303] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

                              [    3.669012] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

                              [    3.676214] usb usb1: Product: xHCI Host Controller

                              [    3.681072] usb usb1: Manufacturer: Linux 4.14.0-xilinx-v2018.2 xhci-hcd

                              [    3.687756] usb usb1: SerialNumber: xhci-hcd.0.auto

                              [    3.692895] hub 1-0:1.0: USB hub found

                              [    3.696580] hub 1-0:1.0: 1 port detected

                              [    3.700670] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller

                              [    3.706081] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2

                              [    3.713762] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.

                              [    3.721868] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003

                              [    3.728582] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

                              [    3.735785] usb usb2: Product: xHCI Host Controller

                              [    3.740643] usb usb2: Manufacturer: Linux 4.14.0-xilinx-v2018.2 xhci-hcd

                              [    3.747327] usb usb2: SerialNumber: xhci-hcd.0.auto

                              [    3.752431] hub 2-0:1.0: USB hub found

                              [    3.756124] hub 2-0:1.0: 1 port detected

                              [    3.760962] rtc_zynqmp ffa60000.rtc: setting system clock to 2038-01-19 03:15:42 UTC (2147483742)

                              [    3.769873] clk: Not disabling unused clocks

                              [    3.774101] ALSA device list:

                              [    3.777011]   #0: DisplayPort monitor

                              [    3.781738] EXT4-fs (mmcblk1p2): couldn't mount as ext3 due to feature incompatibilities

                              [    3.877615] EXT4-fs (mmcblk1p2): warning: checktime reached, running e2fsck is recommended

                              [    3.890736] EXT4-fs (mmcblk1p2): recovery complete

                              [    3.897119] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)

                              [    3.905154] VFS: Mounted root (ext4 filesystem) on device 179:2.

                              [    3.914720] devtmpfs: mounted

                              [    3.917718] Freeing unused kernel memory: 512K

                              [    4.985441] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)

                              [    5.003619] systemd[1]: Detected architecture arm64.

                               

                              Welcome to Debian GNU/Linux 9 (stretch)!

                               

                              [    5.030298] systemd[1]: Set hostname to <debian-zcu102>.

                              [    5.531902] systemd[1]: [/etc/systemd/system/rc-local.service:11] Support for option SysVStartPriority= has been removed and it is ignored

                              [    5.556298] systemd[1]: Listening on udev Kernel Socket.

                              [  OK  ] Listening on udev Kernel Socket.

                              [    5.573146] systemd[1]: Listening on Journal Audit Socket.

                              [  OK  ] Listening on Journal Audit Socket.

                              [    5.589017] systemd[1]: Listening on udev Control Socket.

                              [  OK  ] Listening on udev Control Socket.

                              [    5.605003] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.

                              [  OK  ] Listening on /dev/initctl Compatibility Named Pipe.

                              [    5.628985] systemd[1]: Listening on Syslog Socket.

                              [  OK  ] Listening on Syslog Socket.

                              [    5.645009] systemd[1]: Listening on Journal Socket.

                              [  OK  ] Listening on Journal Socket.

                              [  OK  ] Started Dispatch Password Requests to Console Directory Watch.

                              [  OK  ] Listening on Journal Socket (/dev/log).

                              [  OK  ] Reached target Sockets.

                              [  OK  ] Reached target Remote File Systems.

                              [  OK  ] Started Forward Password Requests to Wall Directory Watch.

                              [  OK  ] Reached target Paths.

                              [  OK  ] Reached target Swap.

                              [  OK  ] Created slice System Slice.

                              [  OK  ] Created slice system-getty.slice.

                              [  OK  ] Created slice system-serial\x2dgetty.slice.

                                       Starting Journal Service...

                                       Starting Remount Root and Kernel File Systems...

                              [  OK  ] Reached target Slices.

                                       Mounting Debug File System...

                                       Mounting POSIX Message Queue File System...

                                       Starting Create Static Device Nodes in /dev...

                                       Starting Load Kernel Modules...

                              [  OK  ] Reached target Encrypted Volumes.

                                       Starting Nameserver information manager...

                              [  OK  ] Mounted Debug File System.

                              [  OK  ] Mounted POSIX Message Queue File System.

                              [  OK  ] Started Journal Service.

                              [  OK  ] Started Remount Root and Kernel File Systems.

                              [  OK  ] Started Create Static Device Nodes in /dev.

                              [  OK  ] Started Load Kernel Modules.

                                       Mounting Configuration File System...

                                       Starting Apply Kernel Variables...

                                       Starting udev Kernel Device Manager...

                                       Starting udev Coldplug all Devices...

                                       Starting Load/Save Random Seed...

                              [  OK  ] Reached target Local File Systems (Pre).

                              [  OK  ] Reached target Local File Systems.

                                       Starting Flush Journal to Persistent Storage...

                              [  OK  ] Mounted Configuration File System.

                              [  OK  ] Started Nameserver information manager.

                              [  OK  ] Started Apply Kernel Variables.

                                       Starting Raise network interfaces...

                              [    6.222819] systemd-journald[1762]: Received request to flush runtime journal from PID 1

                              [  OK  ] Started Flush Journal to Persistent Storage.

                                       Starting Create Volatile Files and Directories...

                              [  OK  ] Started Load/Save Random Seed.

                              [  OK  ] Started Create Volatile Files and Directories.

                                       Starting Update UTMP about System Boot/Shutdown...

                              [  OK  ] Reached target System Time Synchronized.

                              [  OK  ] Started Update UTMP about System Boot/Shutdown.

                              [  OK  ] Started udev Coldplug all Devices.

                              [  OK  ] Started udev Kernel Device Manager.

                              [  OK  ] Reached target System Initialization.

                              [  OK  ] Started Daily Cleanup of Temporary Directories.

                              [  OK  ] Reached target Basic System.

                                       Starting getty on tty2-tty6 if dbus and logind are not available...

                              [  OK  ] Started Regular background program processing daemon.

                              [  OK  ] Started Daily apt download activities.

                              [  OK  ] Started Daily apt upgrade and clean activities.

                              [  OK  ] Reached target Timers.

                                       Starting System Logging Service...

                              [  OK  ] Found device /dev/ttyPS0.

                              [  OK  ] Started getty on tty2-tty6 if dbus and logind are not available.

                              [  OK  ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.

                              [  OK  ] Reached target Sound Card.

                              [  OK  ] Started System Logging Service.

                              [    7.548942] pps pps0: new PPS source ptp0

                              [    7.552899] macb ff0e0000.ethernet: gem-ptp-timer ptp clock registered.

                              [    7.559613] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

                              [  OK  ] Started Raise network interfaces.

                              [  OK  ] Reached target Network.

                                       Starting OpenBSD Secure Shell server...

                                       Starting Permit User Sessions...

                              [  OK  ] Reached target Network is Online.

                                       Starting /etc/rc.local...

                                       Starting LSB: Start NTP daemon...

                              [  OK  ] Started Permit User Sessions.

                              [  OK  ] Started /etc/rc.local.

                              [  OK  ] Started Getty on tty5.

                              [  OK  ] Started Getty on tty1.

                              [  OK  ] Started Getty on tty3.

                              [  OK  ] Started Getty on tty6.

                              [  OK  ] Started Getty on tty2.

                              [  OK  ] Started Getty on tty4.

                              [  OK  ] Started Serial Getty on ttyPS0.

                              [  OK  ] Reached target Login Prompts.

                              [  OK  ] Started OpenBSD Secure Shell server.

                              [   10.701133] macb ff0e0000.ethernet eth0: link up (1000/Full)

                              [   10.706739] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

                               

                              Debian GNU/Linux 9 debian9 ttyPS0

                               

                              debian9 login: root

                              Password:

                              Last login: Mon Jan 18 23:00:44 EST 2038 on ttyPS0

                              Linux debian9 4.14.0-xilinx-v2018.2 #1 SMP Tue Jul 23 12:14:41 EDT 2019 aarch64

                               

                              The programs included with the Debian GNU/Linux system are free software;

                              the exact distribution terms for each program are described in the

                              individual files in /usr/share/doc/*/copyright.

                               

                              Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent

                              permitted by applicable law.

                              root@debian9:~# df

                              Filesystem     1K-blocks    Used Available Use% Mounted on

                              /dev/root       27633676 1920436  24230080   8% /

                              devtmpfs         1892208       0   1892208   0% /dev

                              tmpfs            2023536       0   2023536   0% /dev/shm

                              tmpfs            2023536    9520   2014016   1% /run

                              tmpfs               5120       0      5120   0% /run/lock

                              tmpfs            2023536       0   2023536   0% /sys/fs/cgroup

                              root@debian9:~#

                            • Re: Ultrazed-EV bootconsole [cdns0] disabled
                              khabnl

                              Boot problem is fixed referenced as below:

                               

                              https://forums.xilinx.com/t5/Embedded-Development-Tools/Beginners-problems-with-Ultrazed-eg/td-p/800802

                               

                                  Stop U-Boot when it says "Hit any key to stop autoboot".

                                  Copy this line in the terminal:

                               

                                  setenv bootargs 'earlycon clk_ignore_unused root=/dev/mmcblk1p2 rw rootwait'

                                  env save

                               

                                 power cycle

                               

                               

                              Next I am going to create a new custom Vivado2018.2 project and will test again.

                               

                              Thanks,

                              Kiman

                                • Re: Ultrazed-EV bootconsole [cdns0] disabled
                                  zedhed

                                  Thank you for sharing your progress with the community Kiman!

                                   

                                  So your bootargs from PetaLinux were being overridden by ones kept in persistent NVM storage for U-Boot?

                                   

                                  Best Regards,

                                   

                                  -Kevin

                                    • Re: Ultrazed-EV bootconsole [cdns0] disabled
                                      khabnl

                                      Hi Kevin,

                                       

                                      >>So your bootargs from PetaLinux were being overridden by ones kept in persistent NVM storage for U-Boot?

                                       

                                      I think yes, but not sure! see below message from U-Boot console.

                                       

                                       

                                      U-Boot 2018.01 (Jul 23 2019 - 12:06:10 -0400) Xilinx ZynqMP ZCU102 rev1.0

                                       

                                       

                                      ZynqMP> setenv bootargs 'earlycon clk_ignore_unused root=/dev/mmcblk1p2 rw rootwait'

                                      ZynqMP> env save

                                      Saving Environment to SPI Flash...

                                      SF: Detected n25q256a with page size 512 Bytes, erase size 128 KiB, total 64 MiB

                                      Erasing SPI flash...Writing to SPI flash...done

                                      ZynqMP>

                                       

                                       

                                      Thanks,

                                      Kiman

                                • Re: Ultrazed-EV bootconsole [cdns0] disabled
                                  khabnl

                                  Hi Kevin,

                                   

                                  Do you have the  Vivado2018.2 project for build BSP?

                                  Because I create a my own Vivado 2018.2 project and build petalinux image but is doesn't work (the same as vivado 2019.1).

                                   

                                  I'd like to use your vivado project.

                                   

                                  Kiman

                            • Re: Ultrazed-EV bootconsole [cdns0] disabled
                              narrucmot

                              Hi Kiman,

                               

                              The last boot message you see here ("bootconsole [cdns0] disabled") usually has nothing to do with the bootconsole being disabled.  This message just happens to be the spot where the kernel boot got hung up.  Because of the way STDIO messages are buffered to the UART during boot, this is the last message that is seen by the user.  The problem is somewhere else.  The u-boot messages indicate this is a kernel that expects a RAMdisk rootfs (“## Loading ramdisk from FIT Image at 10000000 ...”), but the bootargs in the system-user.dtsi file indicate a rootfs on the SD card (“root=/dev/mmcblk0p2 rw  rootfstype=ext4 rootwait”).  These settings re inconsistent.  I would expect the bootargs for a kernel mounting a RAMdisk to look much simpler (“bootargs = "earlycon clk_ignore_unused"”).  If there truly is a rootfs on the mmcblk0p2 partition then PetaLinux also needs to be configured (and thus u-boot) for that.  I believe Xilinx UG1144 describes this (https://www.xilinx.com/support/documentation/sw_manuals/xilinx2019_1/ug1144-petalinux-tools-reference-guide.pdf ).

                               

                              --Tom

                                • Re: Ultrazed-EV bootconsole [cdns0] disabled
                                  khabnl

                                  Hi Tom,

                                   

                                  Thank you for your response.

                                   

                                  Actually I tried to simple way but I got the same result.

                                  bootargs = "console=ttyPS0,115200 earlycon clk_ignore_unused";

                                  stdout-path = "serial0:115200n8";

                                   

                                  I need the SD card /dev/mmcblk0p2 partition for the Debian rootfs.

                                   

                                  Thanks,

                                  Kiman

                                  1 of 1 people found this helpful
                                    • Re: Ultrazed-EV bootconsole [cdns0] disabled
                                      khabnl

                                      I create image.ub using petalinux version 2019.1

                                      But the kernel image log file shows "Linux version 4.9.0-xilinx-v2017.3 (avnet@ubuv1604) (gcc version 6.2.1 20161016"

                                       

                                      I think this is something wrong, image.ub booting from existing avnet image instead of the SD card?

                                      Starting kernel ...

                                       

                                       

                                      [    0.000000]
                                      Linux version 4.9.0-xilinx-v2017.3 (avnet@ubuv1604) (gcc version 6.2.1 20161016
                                      (Linaro GCC 6.2-2016.11) ) #1 SMP Tue Feb 6 17:51:04
                                      EST 2018

                                      1 of 1 people found this helpful
                                        • Re: Ultrazed-EV bootconsole [cdns0] disabled
                                          drozwood90

                                          Hi there,

                                           

                                          It sounds like you might be booting from the onboard EEPROM or other memory.  Check your boot switch configuration to ensure that you are targeting booting from the SDCARD.

                                           

                                          --Dan

                                          1 of 1 people found this helpful
                                            • Re: Ultrazed-EV bootconsole [cdns0] disabled
                                              khabnl

                                              Hi Dan,

                                               

                                              Yes, I configured booting from the SD card, and  I confirmed several times.

                                              Avnet default is QSPI (OFF,ON,ON,ON).

                                              The SD card booting is (OFF, ON, OFF, ON).

                                              If remove SDCARD there is no serial console message.

                                               

                                              If you see U-Boot message it indicate on Jul 19 2019, but Kernel is not 2019.1

                                               

                                               

                                              U-Boot 2019.01 (Jul 19 2019 - 14:29:54 +0000)

                                               

                                              Board: Xilinx ZynqMP

                                              DRAM:  4 GiB

                                              usb dr_mode not found

                                              EL Level:       EL2

                                              Chip ID:        zu7ev

                                              MMC:   mmc@ff160000: 0, mmc@ff170000: 1

                                              Loading Environment from SPI Flash... SF: Detected n25q256a with page size 512 Bytes, erase size 128 KiB, total 64 MiB

                                              *** Warning - bad CRC, using default environment

                                               

                                               

                                              Thanks,

                                              Kiman

                                                • Re: Ultrazed-EV bootconsole [cdns0] disabled
                                                  khabnl

                                                  Hello,

                                                   

                                                  I revisited my ultrazed EV SD card booting project.

                                                  I create a new Vivado 2018.2 project based on uz7ev_evcc_sd_oob_2018_2,bsp.

                                                  And now I can booting-up fro SD card.

                                                   

                                                   

                                                  #ultrazed_ev SD card booting
                                                  # boot   : FAT32
                                                  # footfs : Ext4 partition, Debian 10

                                                   

                                                  # Create a new project preate from uz7ev_evcc_sd_oob_2018_2,bsp

                                                  $petalinux-create -t project -s uz7ev_evcc_sd_oob_2018_2.bsp -n uz7ev_evcc_sd_oob_2018_2_mytest

                                                   

                                                  $cd uz7ev_evcc_sd_oob_2018_2_mytest

                                                   

                                                  # uz_petalinux.sdk is my new Vivado project 2018.2, new project based on bsp UZ7EV_EVCC
                                                  $petalinux-config --get-hw-description=/home/bpmlab2/xilinx/kiman/ultrazed_ev/2018.2/uz_petalinux.sdk

                                                   

                                                  $petalinux-build

                                                   

                                                  #Create BOOT.bin
                                                  $petalinux-package --boot --format BIN --fsbl images/linux/zynqmp_fsbl.elf --u-boot images/linux/u-boot.elf --pmufw images/linux/pmufw.elf --fpga images/linux/system.bit --force

                                                   

                                                   

                                                   

                                                  Thank for your support.

                                                   

                                                  Release 2018.2   Aug 15 2019  -  21:20:32
                                                  NOTICE:  ATF running on XCZU7EV/silicon v4/RTL5.1 at 0xfffea000
                                                  NOTICE:  BL31: Secure code at 0x0
                                                  NOTICE:  BL31: Non secure code at 0x8000000
                                                  NOTICE:  BL31: v1.4(release):xilinx-v2018.1-4-g93a69a5a
                                                  NOTICE:  BL31: Built : 01:18:22, Aug 16 2019
                                                  PMUFW:  v1.0

                                                  U-Boot 2018.01 (Aug 15 2019 - 21:18:06 -0400) Xilinx ZynqMP ZCU102 rev1.0

                                                  I2C:   ready
                                                  DRAM:  4 GiB
                                                  EL Level:       EL2
                                                  Chip ID:        zu7ev
                                                  MMC:   sdhci@ff160000: 0 (eMMC), sdhci@ff170000: 1 (SD)
                                                  SF: Detected n25q256a with page size 512 Bytes, erase size 128 KiB, total 64 MiB
                                                  In:    serial@ff000000
                                                  Out:   serial@ff000000
                                                  Err:   serial@ff000000
                                                  Board: Xilinx ZynqMP
                                                  Net:   ZYNQ GEM: ff0e0000, phyaddr 0, interface rgmii-id
                                                  eth0: ethernet@ff0e0000
                                                  Hit any key to stop autoboot:  0
                                                  Device: sdhci@ff160000
                                                  Manufacturer ID: 13
                                                  OEM: 14e
                                                  Name: Q2J55
                                                  Tran Speed: 200000000

                                                   

                                                  [    3.817126] EXT4-fs (mmcblk1p2): couldn't mount as ext3 due to feature incompatibilities
                                                  [    3.979175] EXT4-fs (mmcblk1p2): recovery complete
                                                  [    3.985284] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
                                                  [    3.993315] VFS: Mounted root (ext4 filesystem) on device 179:2.
                                                  [    4.002864] devtmpfs: mounted
                                                  [    4.005876] Freeing unused kernel memory: 512K
                                                  [    4.738733] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
                                                  [    4.760315] systemd[1]: Detected architecture arm64.

                                                  Welcome to Debian GNU/Linux 10 (buster)!

                                                  [    4.782154] systemd[1]: Set hostname to <debian10-zcu102>.
                                                  [    5.084836] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
                                                  [    5.101838] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
                                                  [    5.337221] systemd[1]: Listening on Journal Audit Socket.
                                                  [  OK  ] Listening on Journal Audit Socket.
                                                  [    5.357344] systemd[1]: Listening on Journal Socket.
                                                  [  OK  ] Listening on Journal Socket.
                                                  [    5.374570] systemd[1]: Mounting POSIX Message Queue File System...
                                                           Mounting POSIX Message Queue File System...
                                                  [    5.397326] systemd[1]: Listening on initctl Compatibility Named Pipe.
                                                  [  OK  ] Listening on initctl Compatibility Named Pipe.
                                                  [    5.422311] systemd[1]: Starting Remount Root and Kernel File Systems...
                                                           Starting Remount Root and Kernel File Systems...
                                                  [  OK  ] Listening on udev Kernel Socket.
                                                  [  OK  ] Reached target Swap.
                                                  [  OK  ] Created slice system-getty.slice.
                                                           Mounting Huge Pages File System...
                                                  [  OK  ] Listening on Syslog Socket.
                                                  [  OK  ] Listening on udev Control Socket.
                                                           Starting Load Kernel Modules...
                                                  [  OK  ] Started Forward Password R…uests to Wall Directory Watch.
                                                           Starting udev Coldplug all Devices...
                                                  [  OK  ] Started Dispatch Password …ts to Console Directory Watch.
                                                  [  OK  ] Reached target Local Encrypted Volumes.
                                                  [  OK  ] Reached target Paths.
                                                           Mounting Kernel Debug File System...
                                                  [  OK  ] Listening on Journal Socket (/dev/log).
                                                  [  OK  ] Reached target Sockets.
                                                  [  OK  ] Reached target Slices.
                                                  [  OK  ] Created slice system-serial\x2dgetty.slice.
                                                           Starting Journal Service...
                                                  [  OK  ] Reached target Remote File Systems.
                                                  [  OK  ] Mounted POSIX Message Queue File System.
                                                  [  OK  ] Started Remount Root and Kernel File Systems.
                                                  [  OK  ] Mounted Huge Pages File System.
                                                  [  OK  ] Started Journal Service.
                                                  [  OK  ] Started Load Kernel Modules.
                                                  [  OK  ] Mounted Kernel Debug File System.
                                                           Mounting Kernel Configuration File System...
                                                           Starting Apply Kernel Variables...
                                                           Starting Flush Journal to Persistent Storage...
                                                           Starting Create System Users...
                                                           Starting Load/Save Random Seed...
                                                  [  OK  ] Mounted Kernel Configuration File System.
                                                  [  OK  ] Started Apply Kernel Variables.
                                                  [  OK  ] Started Load/Save Random Seed.
                                                  [  OK  ] Started Create System Users.
                                                           Starting Create Static Device Nodes in /dev...
                                                  [    5.961644] systemd-journald[2183]: Received request to flush runtime journal from PID 1
                                                  [  OK  ] Started Flush Journal to Persistent Storage.
                                                  [  OK  ] Started Create Static Device Nodes in /dev.
                                                  [  OK  ] Reached target Local File Systems (Pre).
                                                  [  OK  ] Reached target Local File Systems.
                                                           Starting udev Kernel Device Manager...
                                                           Starting Create Volatile Files and Directories...
                                                  [  OK  ] Started udev Coldplug all Devices.
                                                           Starting Helper to synchronize boot up for ifupdown...
                                                  [  OK  ] Started Create Volatile Files and Directories.
                                                           Starting Update UTMP about System Boot/Shutdown...
                                                           Starting Network Time Synchronization...
                                                  [  OK  ] Started udev Kernel Device Manager.
                                                  [  OK  ] Started Update UTMP about System Boot/Shutdown.
                                                  [  OK  ] Found device /dev/ttyPS0.
                                                  [  OK  ] Started Network Time Synchronization.
                                                  [  OK  ] Started Helper to synchronize boot up for ifupdown.
                                                           Starting Raise network interfaces...
                                                  [  OK  ] Listening on Load/Save RF …itch Status /dev/rfkill Watch.
                                                  [  OK  ] Reached target System Time Synchronized.
                                                  [  OK  ] Reached target System Initialization.
                                                  [  OK  ] Started Daily Cleanup of Temporary Directories.
                                                  [    8.405605] pps pps0: new PPS source ptp0
                                                  [    8.409568] macb ff0e0000.ethernet: gem-ptp-timer ptp clock registered.
                                                  [    8.416253] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
                                                  [  OK  ] Started Daily man-db regeneration.
                                                  [  OK  ] Started Daily apt download activities.
                                                  [  OK  ] Started Daily apt upgrade and clean activities.
                                                  [  OK  ] Reached target Basic System.
                                                           Starting getty on tty2-tty…nd logind are not available...
                                                           Starting System Logging Service...
                                                  [  OK  ] Started Regular background program processing daemon.
                                                  [  OK  ] Started Daily rotation of log files.
                                                  [  OK  ] Reached target Timers.
                                                  [  OK  ] Reached target Sound Card.
                                                  [  OK  ] Started Raise network interfaces.
                                                  [  OK  ] Reached target Network.
                                                           Starting Permit User Sessions...
                                                           Starting OpenBSD Secure Shell server...
                                                  [  OK  ] Started Permit User Sessions.
                                                  [  OK  ] Started System Logging Service.
                                                  [  OK  ] Started Getty on tty2.
                                                  [  OK  ] Started Serial Getty on ttyPS0.
                                                  [  OK  ] Started Getty on tty1.
                                                  [  OK  ] Started Getty on tty3.
                                                  [  OK  ] Started Getty on tty4.
                                                  [  OK  ] Started Getty on tty5.
                                                  [  OK  ] Started Getty on tty6.
                                                  [  OK  ] Started getty on tty2-tty6… and logind are not available.
                                                  [  OK  ] Reached target Login Prompts.
                                                  [  OK  ] Started OpenBSD Secure Shell server.
                                                  [  OK  ] Reached target Multi-User System.
                                                  [  OK  ] Reached target Graphical Interface.
                                                           Starting Update UTMP about System Runlevel Changes...
                                                  [  OK  ] Started Update UTMP about System Runlevel Changes.

                                                  Debian GNU/Linux 10 debian10 ttyPS0

                                                  debian10 login:

                                                  1 of 1 people found this helpful